|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good product and very helpfull to repair. Many thanks.
;
Very good product. Best service manual. Many thanks
;
I am only search for 5 Minute, by it in 5 Minutes to and get ist in few ours! Best i found in the Internet and my Amplifer is repaired as well! Thank you
 ;
Readable text and good copy. Very much needed if you wish to do some repairs on this fine old unit.
;
Fint forløb med levering af manualen. Kvaliteten af skanningen betegnes som middel
CHAPTER 2
1 . Procedure
Component to be removed
DISASSEMBLY
The numbers in the followinng tables correspond to those in Fig. 1-1. Remove each component shown in the following tables according to the order of the numbers. Item Front case (1) Top case (1) (2) Rear panel (1) (2) (3) (4) (5) Rear PWR EXT & PC f r a m e c i r c u i t circuit a ' s s y board board (1) (1) (1) (2) (2) (2) (3) (3) (3) (4) (4) (4) (5) (5) (5) (6) (6) (6) (7) (7) (8) (8) (9) (10) (11) (12) (13) (14) (15) How to remove
(1) Remove 1 screw holding the front case. (2) Remove 4 screws holding the top case. (3) Remove 2 screws holding the rear panel. (4) Remove 2 screws holding the bottom case. (5) Release 2 tabs. (6) Remove 2 screws. (7) Disconnect 2 connectors on the BNC circuit board. (8) Disconnect 1 connector on the AC circuit board. (9) Remove 2 screws holding the PWR frame. (10) Disconnect 1 connector on the PWR circuit board. (11) Remove 3 screws holding the PWR circuit board. (12) Disconnect 3 connectors on the PC circuit board. (13) Remove 2 screws holding the bottom case. (14) Remove 1 screw and remove the EXT circuit board in the direction of the arrow. (15) Remove the PC circuit board in the direction of the arrow.
Removal Procedure and Number of Component to be removed
Lens CCD AC BNC SW Bottm I t e m b l o c k sensor & c i r c u i tc i r c u i tc i r c u i t c a s e S circuit b o a r d b o a r d b o a r d (1) board & AC (1) (2) (1) terminal ( 1 ) (1) (2) (3) (2) (1) (2) (2) (3) (4) (3) (2) (3) (3) (4) (5) (4) (3) (4) (4) (5) (6) (5) (4) (5) (5) (6) (6) (5) (6) (6) (7) (6) (7) (7) (8) (7) (8) (8) (12) (8) (13) (12) (14) (13) (14) (15) (15) (16) (17) (16) (18) (17) (18) (19) (20) (21) (22)
How
to
remove
(23)
(23) (24) (25)
(26)
(1) Remove 1 screw holding the front case. (2) Remove 4 screws holding the top case. (3) Remove 2 screws holding the rear panel. (4) Remove 2 screws holding the bottom case. (5) Release 2 tabs. (6) Remove 2 screws. (7) Disconnect 2 connectors on the BNC circuit board. (8) Disconnect 1 connector on the AC circuit board. Note: Steps (9) to (11) are not necessary. (12) Disconnect 3 connectors on the PC circuit board. (13) Remove 2 screws holding the bottom case. (14) Remove 1 screw and remove the EXT circuit board in the direction of the arrow. (15) Remove the PC circuit board in the direction of the arrow. (16) Disconnect 1 connector on the S circuit board. (17) Remove 2 screws holding the lens block. (*1) (18) Remove 4 screws holding the lens block. (19) Unsolder 14 points (CCD sensor) on the S circuit board. (20) Remove 2 screws holding the S circuit board. (21) Remove 2 screws holding the AC terminal. (22) Unsolder 2 points on the AC circuit board. (23) Unsolder 2 points on the BNC circuit board. (24) Unsolder 9 points on the SW circuit board. (25) Remove 1 screw holding the SW circuit board. (26) Remove 2 screws holding the bottom case.
*1: When the lens block is removed, the crystal filter and rubber are also removed. Be careful not to damege and lose them.
2-1
|
|
|
> |
|
