|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
;
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
 ;
You can fully trust on this one!
All the schematics are very crear an in one piece per page
;
I have never bought a service manual which is as competely readable as this althogh it was a scanned pdf. Thank you for this succesful manual also cheaper than other sites.
;
Thanks for a very good and readable servicemanual. Just what I needed as a "dinosaur technician". I really recommmend this site and will come back.
Åsbjörn
VL-PD3AS/AH/AE
3. DISASSEMBLY OF THE SET
Note: Before removing the cabinet, turn off the power supply, and ascertain that the battery have been removed. 1. 5.
V/F section
(D) (D) (D) (C) (D)
(G)
· Remove the screws ((D)XiPSF17P03000)(4pcs.) of the bottom · Up the section of V/F, and remove the screw ((D)XiPSF17P03000) cover and them. (1pc.). · Remove the screws ((D)XiPSF17P03000)(2pcs.) and ((C) 2. XiPSF1704000)(1pc.). · Remove the screw ((G)XiPSN17P03000)(1pc.) and battery cover.
(F)
6.
(F)
(D)
(B) (F) (R)
· Remove the screws ((F)XiPSN17P04000)(3pcs.), ((B)LXHZ0050TAFN)(1pc.) of the front cover and the DV terminal's screw ((R)XiPSN16P05000)(1pc.).
3.
Remove the claw
(D)
(D)
(D)
· Remove the screw ((D)XiPSF17P03000)(1pc.) of topside and open the cassette compartment door, remove the screws ((D)XiPSF17P03000) (3pcs.) of both sides and center screws. Remove the Remote control receiver unit connector, the Zoom FPC, the EJECT switch connector, the H/A connector, and the cabinet A.
(B)
7.
(D)
· Open the LCD panel, remove the screws ((B)LX-HZ0050TAFN) (2pcs.), the claws what is connected the cabinet A and remove the front cover. Be careful so that not damage the lead wires of microphone when it removes the front cover.
(H)
4.
(G) (G)
· Remove the screw ((D)XiPSF17P03000)(1pc.) topside of cabinet B and the screws ((H)XiPSN17P02000)(1pc.) of side surface and ((G) XiPSN17P03000)(1pc.) of rear surface.
Microphone connector
(Note.) In case of disassemble or assemble the section of V/F, do the work with great care that there are never taint or intermix of dust.
· Slide the section of V/F, and remove the plate of topside, the screws ((G)XiPSN17P03000)(2pcs.), and remove the top cover what is slided toward V/F slide.
4
|
|
|
> |
|
