|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
;
I was skeptical at first but later found the manual to be good quality for the price. It took a couple hours to receive the email with the download link, well worth the wait. Thanks.
;
very helpful, I could not have cleaned motherboard and replaced the main fan without it
 ;
Good manual, schematics nice and clear with good quality scanning. Woul dhave been nice to have immediate access after purchasing though.
;
I was very glad recieving the service manal from You. Manuals were delivered promptly and were correct as advertised. A complete and very usefull service manual with all details. Thank you!
VL-Z100S-S/H-S/E-S VL-Z300S-S/H-S/E-S
5. INSPECTION AND MAINTENANCE ITEMS AND INTERVALS
In order to maintain the quality of the mechanism section, perform the following maintenance and inspection. After repairing the mechanism section, perform the following maintenance regardless of the number of hours of use by the user.
5-1. Maintenance and inspection list
Inspection and maintenance location Tape running section (See7-3.) Drum section, Video head (See 7-3.) 500 Number of hours of use (h) 1,000 1,500 2,000 3,000
� � � Replace.
� � � Clean.
� � � Lubricate.
� � � Check.
Symptoms observed at the time of maintenance � Block noise � Clogging of head � Damage to tape
Notes and remarks Note: If no envelope output is obtained in spite of the video head being cleaned, replace the drum component. (If the envelope output is normal, refer to "10. USEFUL TIPS".) � Replace if any abnormal condition is found.
<Rollers> � Replace if abnormal rotation or swing (large) is found. <Others> � Cleans the portions that come in contact with the tape (the lower drum helical portion in particular). Use the specified cleaning liquid. Pinch roller Capstan motor (Timing belt) Swing arm S reel table, Tu reel table Center gear boss Relay pulley shaft � Tape not running � Tape sagged � Block noise � Abnormal noise
� Abnormal noise
� Apply oil. [Oil] Cosmo Hydro HV22 Note: Apply oil to the shaft and lightly wipe it off with a cloth. � Replace if any abnormal condition (noise etc.) is found. � If a part is out of spec, replace it.
Loading motor Mode SW Abnormal noise
� Ejecting cannot be made. � Mode cannot be set. � Tape not running � Tape sagged � Damage to tape � Abnomaly in reproduced picture
Performance check Driving Running system
PB and VS/R winding torque PB, VS/R and loading back tension S reel table unloaded torque
[Oil] Cosmo Hydro HV22 [Grease] Molykote YM-103 Sankei Chemical CFD-409Z
[Loctite adhesive] Three Bond 1401B [Cleaning liquid] Industrial ethyl alcohol
5-2. Cautions in handling the mechanism
(1) Cut washers removed at the time of part replacement etc. should be replaced with new ones without fail. (2) Because no volume adjustment is available in this mechanism, cleaning or part replacement should be performed if the setting is not satisfied. (3) About oil a) Be sure to use the specified oil. (If any oil other than the specified oil is used, various troubles will occur.) b) When lubricating the bearing, be sure to oil free from foreign particles such as dust. (If oil in which foreign particles such as dust are mixed is used, it will cause wear and seizure to the bearing.) c) The term "One drop of oil" here means the amount of oil on the point of a needle etc. shown in Fig.1. (4) Repairing of circuits, final adjustment of running system, etc. should be performed with the cassette controller assembly installed in the mechanism. (5) When operating the mechanism singly, apply voltage to the loading motor to drive it. The voltage between the terminals should be 3 to 4V DC. (Do not apply external voltage to the loading motor with the mechanism connected with the main circuit board. Doing so could cause a failure.) (Turning the gears forcedly by hand may cause them to get damaged.) When placing the mechanism singly, use an appropriate spacer so that the capstan motor is not rubbed. (6) When installing the cassette controller, push the portion indicated by "A" in Fig.2. Do not push other portions. (7) Take care not to deform the components of the mechanism.
Oil
�1.5 or less Fig. 1
Fig. 2
9
|
|
|
> |
|
