|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was searching a way to modify the original phono-in entry (for connection of vynil disc player, with RIAA equalization) to a line-in entry (for connection of modern analog entries, eg. ipod, mp3player).
This service manual gave me the correct hints.
It contains very useful infos for repairing and modifing the hi-fi, such as disassembling instructions, block diagrams, schematic diagrams, PCB prints, replacement parts list.
Very good!
;
Great Job!!! clear and efficient as always!!
it is really nice to have peple that are doing such a good work!!!!!
;
I must admit, I was very skeptical... $4.99 for a 74 page service manual. I've seen some very poorly scanned manuals on the Internet, but this one is VERY good quality! Even when zooming into 500%. Great Deal!
;
Very good detail, Quick service response. A useful service manual with all details. I recomend this service.
;
As Always you can find here manuals even of difficult TV scheme which are scan in almost perfect way.clear and fast!!!!!
Great work thanks!
VN-EZ1C
VN-EZ1U
4. DISASSEMBLY OF THE SET
~For assembly, tighten the screw to the torque of 0.5+0.1/-0 kg cm. ~Previously remove the smart medium unit. 1. Front cabinet 6. H x2
2
SHUTTER PWB C G C
C
Battery lid B 1 A x1 H
POWER PWB MAIN PWB
· Remove the screws ( A LX-BZ0210TAFN)(1pcs.) and ( B LX- · Remove the screws ( C LX-HZ0058TAFF)(2pcs.) and ( G LXHZ0056TAFN)(1pcs.) and ( H LX-BZ0208TAFN)(3pcs.). HZ0206TAFN)(1pcs.). · Open the battery lid as instructed with 1. · Pressing the power PWB to prevent it from floating, lift the main · Remove the front cabinet, lifting it as instructed with 2. PWB in the arrow direction. (Take care that the board-to-board connector is slightly inner than the center.) 2. D x2 · Remove the screw ( C LX-HZ0058TAFF) of the shutter PWB, D x2 and the main PWB will be removed.
Lens unit
7.
Battery connector
B Tapping Back light connector TFT PWB FFC JACK PWB
MAIN PWB
· Remove the screws ( B LX-HZ0056TAFN)(1pcs.) and ( D LX-
HZ0062TAFF)(4pcs.). · Remove the JAK PWB screw ( D LX-HZ0062TAFF)(1pcs.), the · Lift the lens unit, and remove the CCD flex and tilt connector battery connector, TFT PWB FFC and back light connector, and across the main PWB. the power PWB will be removed. · Remove the operation key flex connector and SP microphone Note: As far as the power PWB is routed to , connect the black lead
connector, and lift the main PWB.
3.
H x2
H x2
wire of the jack PWB directly to the battery terminal. From , solder two lead wires from the battery terminal to the power PWB and the black lead wire from the jack PWB to the land near the battery connector. Lens unit
8.
H x2
H x1
H x2 H x1
· Remove the screws ( H LX-BZ0208TAFN)(7pcs.).
4.
CCD PWB
H x2
· Remove the screws ( H LX-BZ0208TAFN)(3pcs.).
9.
TFT flex
· Remove the screws ( H LX-BZ0208TAFN)(2pc.). · Remove the CCD flex.
5.
· Remove the TFT flex. TFT · Pull off TFT in the arrow direction.
10.
CCD PWB
H x1
TFT PWB
· Remove the CCD PWB.
· Remove the screw ( H LX-BZ0208TAFN), and TFT PWB will be removed.
4-1
|
|
|
> |
|
