|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual is excellent, well detailed, and divided into two parts. Received very quickly. Thank you.
;
a solid deal - quick and without any problems.
I life in europe - with downloads no loosing time
once again
 ;
got exactly what i ordered in a very timely manner. will use again for other manuals
;
I'm happy. Good quality. Very helped me with my work..............................
;
This is the second Manual I have ordered from owner-manuals, I give it five stars because it is exactly what I expected given the age of the equipment. So the contents look a bit aged and the pictures a bit grainy, it fulfills my needs and I am glad I can still get hold of them.
Alignment and Adjustment
WHITE ( APPROX. 100% ) APPROX. 0.7V APPROX. 0.3V H
2-12. Y-FM Deviation (Hi8) : This adjustment sets the Y_FM modulation
1.0 0.02Vp-p
level in recording. For adjustment, playback the self-recorded signal and observe the VIDEO OUT signal. Note : It is a little difficult to adjust because you can check the waveform in playback mode even though the adjustment is performed in VCR record mode. So you have to do it carefully. a. Preparations
TAPE EQUIPMENT HI-8 TAPE FOR RECORDING OSCILLOSCOPE NONE CN452 PIN13 OD Y-FM DEVIAT (HI8)
l. Be sure to press the �PROGRAM AE(CONFIRM)� button on FUNCTION to memorize setting. m. Reset the power source so as to fix the new data to the camcorder�s EEPROM.2-11. Y-FM Carrier (Hi8)
2-11. Y-FM Carrier (Hi8) : This adjustment is performed to set the synctip level of the composite video signal. Maladjusted Y-FM carrier impact to the playback picture, there may be black or white dot noise. a. Preparations
TAPE EQUIPMENT OTHER TEST POINT ADDRESS NAME HI8 TAPE FOR RECORDING FREQUENCY COUNTER NONE IC 201 PIN 13 OC Y-FM CARRIER (HI-8)
OTHER TEST POINT ADDRESS NAME
b. Connect a power source. c. Get into the VCR adjustment mode. d. Press the �FADE(MODE UP)� or �BLC(MODE DOWN)� button of FUNCTION so as to select the address OD. e. Insert a Hi-8 Tape to the camcorder. f. Press the �START/STOP� button on the Rear board so as to set the camcorder to RECORDING mode. g. Record for enough time to check the waveform when you playback where you recorded in step f). * 1 minute may be enough to check the waveform in playback mode. i. Make sure that the waveform is to be as below. (If OK, go to step l). j. In case of the waveform level is bigger than 1Vp-p, press the Data Down button so as to set to down the waveform level and if the waveform level smaller than 1Vp-p, press the Data Up button so as to set to up the waveform level.
WHITE ( APPROX. 100% ) APPROX. 0.7V APPROX. 0.3V H 1.0 0.02Vp-p
b. Connect a power source. c. Get into the VCR adjustment mode. d. Press the �FADE(MODE UP)� or �BLC(MODE DOWN)� button of FUNCTION so as to select the address OC. e. Insert aHi-8 Tape to the camcorder. f. Press the �START/STOP� button on the Rear board so as to set the camcorder to RECORDING mode. g. Connect the frequency counter to the addressed Test Point. h. Press the �TITLE(DATA DOWN)/DSE(DATA UP)� button so as to set the frequency to 5.99MHz ±0.02MHz i. Be sure to press the �P.AE(CONFIRM)� button on FUNCTION to memorize setting. j. Reset the power source so as to fix the new data to the camcorder�s EEPROM.
Samsung Electronics
4-47
|
|
|
> |
|
