|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
3-4. Adjust Signal Level
3-4-1. Component Level Adjustments
1. Input the Component signal to the INPUT-A. Then, from INPUT-A of the SET SETTING, select the COMPONENT (15K Component color bar chroma ON). 2. Set the COLOR to 50. 3. Connect the Oscilloscope to the TP5305 (B OUT) of the C board . 4. Enter the item OTHER of Device Adjust of the menu. 5. Set 06 3D GAMMA/ THROUGH : 0 to 06 3D GAMMA/ THROUGH : 1. 6. Set 07 3D GAMMA/ SW : 1 to 07 3D GAMMA/ SW : 0. 7. Advance the item RGB-MTRX of Device Adjust of the menu. 8. Select the item 08 YUV COL. Use the key � or �, or both, to adjust level of two color bars, the left and right end so that they will come to the same level. 9. Select 09 SUB HUE, then adjust the level of centrally adjoining two color bars in the midst of all bars, using the key � or �, or both so that they can be made flat. 10. Press ENTER key and select � SAVE TO MEMORY �. For saving the data, press the ENTER again.
both, to adjust the level of two color bars, the left and right end so that they will come to the same level. 6. Select 09 SUB HUE, then adjust the level of centrally adjoining two color bars in the midst of all bars, using the key � or �, or both so that they can be made flat. 7. Press the ENTER key and select � SAVE TO MEMORY �. 8. For saving the data, press the ENTER key again.
(1080/60i 100% Color bar) Fig. 3-4-2
3-4-3. Adjust 15K RGB Level
1. Set the COLOR to 50. 2. Connect the Oscilloscope to the TP5305 of the C board. 3. Input the Color bar signal 15K RGB 100% to the INPUT-A (5BNC). Select COMPUTOR from the INPUT-A of the SET SETTING. 4. Enter the item RGB MATRX of Device Adjust of the menu. 5. Select the item 08 YUV COL. Use the key � or �, or both, to adjust the level of two color bars, the left and right end so that they will come to the same level. 6. Select 09 SUB HUE, then adjust the level of centrally adjoining two color bars in the midst of all bars, using the key � or �, so that they can be made flat. 7. Press the ENTER key and select � SAVE TO MEMORY �. 8. For saving the data, press the ENTER key again.
Adjust GND to bottom ege in the DC 0.5 V range.
(15K Component color bar/Chroma ON) Fig. 3-4-1
3-4-2. Adjust X2 Component Level
1. Set the COLOR to 50. 2. Connect the Oscilloscope to the TP5305 of the C board. 3. Input the Color bar signal 1080/60i 100% to the INPUT-A. Select the DTV-YPbPr from the INPUT-A of the SET SETTING. 4. Enter the item RGB MATRX of Device Adjust of the menu. 5. Select the item 08 YUV COL. Use the key � or �, or 3-2
(15K RGB 100% Color bar) Fig. 3-4-3
VPL-FX50
|
|
|
> |
|
