|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
1-5-4. DC Fan (for Lamp)
Removal 1. Remove the cabinet. (Refer to Section 1-3.) 2. Remove the C board. (Refer to steps 3 to 7 of Section 1-4-1.) 3. Remove the lamp assembly. (Refer to steps 2 and 3 of Section 1-5-2.) 4. Remove the optical block assembly. (Refer to step 5 of Section 1-5-3.) 5. Remove the two screws (BTP3 x 12), then remove the lamp house. 6. Remove the two screws (BTP3 x 12), then remove the DC fan (for lamp). 7. Remove the two screws (BVTP3 x 6), then remove the thermostat.
BTP 3 x 12 BTP 3 x 12
1-5-5. DC Fan (for Lamp Power Supply) and TA Board
Removal 1. Remove the cabinet. (Refer to Section 1-3.) 2. Remove the C board. (Refer to steps 3 to 7 of Section 1-4-1.) 3. Remove the lamp assembly. (Refer to steps 2 and 3 of Section 1-5-2.) 4. Remove the lamp power supply board. (Refer to step 5 to 11 of Section 1-4-6.) 5. Remove the optical block assembly. (Refer to step 5 of Section 1-5-3.) 6. Remove the two screws (BVTP3 x 20), then remove the fan cover (B) and DC fan (Sirocco) [A]. 7. Remove the five screws (BTP3 x 12), then remove the duct (panel). 8. Remove the three screws (PTP4 x 45), then remove the DC fan (sirocco) [B]. 9. Remove the screw (BTP3 x 12), then remove the TA board.
Lamp house Thermostat
BVTP3 x 20 Fan cover (B)
BVTP 3x8
DC fan (for lamp)
DC fan (sirocco) [A] BTP 3 x 12 TA board
Duct (panel)
BTP 3 x 12
DC fan (sirocco) [B]
PTP4 x 45
Installation 8. Attach the DC fan (for lamp) in the reverse order of steps 5 to 7. 9. Assemble this unit in the reverse order of steps 1 to 4. Installation 10. Attach the DC fan (for lamp power supply) and TA board in the reverse order of steps 6 to 9. 11. Assemble this unit in the reverse order of steps 1 to 5.
VPL-HS50/HS51
1-13
|
|
|
> |
|
