|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The TEAC A-1500's Service Manual was instrumental in reviving this classic reel-to-reel. Not only does it have the schematics, exploded parts diagram and parts list, it also provided mechanical adjustment information that approximate factory default settings.
 ;
This service manual was determinant to enable to fix my Alpine Amplifier. I am pleased with my purchase. For a 5 star rating I would like to see a higher resolution scan of the printed circuit board lay-out because the gray scale grafics was dificult to see. Also some schematic diagrams were scanned at a slight angle. Never the less, it had all information I needed to troubleshoot and service my equipment.
;
Complete manual, the good quality of reproduction allows enlarged print-out of the schematic diagram in the size it probably had in the original print edition and which is necessary for practical use.
;
The service manual was complete and the components on the drawings very good visible.
;
downloaded next day , manual is very helpful , fast and easy
Projecting
Using the MENU
Adjustments and settings using the menu
The projector is equipped with an on-screen menu for making various adjustments and settings. To select the language used in the menu, see page 32 (EN).
To turn off the power
To clear the menu display
Press the MENU key. The menu display disappears automatically if no key is pressed for one minute.
1
Press the I / u key on the Remote Commander or on the control panel. The following message appears to confirm if you want to turn off the power.
1
Press the MENU key. The menu display appears. The menu presently selected is highlighted in blue.
I NPUT�A P I CTURE CTRL CONTRAST : 80 BR I GHT : 50 GAMMA MODE : GRAPH I CS COLOR TEMP : H I GH
To reset items that have been adjusted
Press the RESET key. �Complete!� appears on the screen and the settings appearing on the screen will be reset to their factory preset values. Items which can be reset are: � �CONTRAST�, �BRIGHT�, �COLOR�, �HUE�, and �SHARP� in the PICTURE CTRL menu � �DOT PHASE�, �SIZE�, and �SHIFT� in the INPUT SETTING menu.
POWER OFF? P l ea s e p r e s s
key / u i n . I aga
Note
The message will disappear if you press any key except the I / u key, or if you do not press any key for five seconds.
2
2
Press the I / u key on the Remote Commander or on the control panel again. The ON indicator flashes in green and the fan continues to run for about 90 seconds to reduce the internal heat. Also, the ON indicator flashes quickly for the first 30 seconds. During this time, you will not be able to turn the power back on with the I / u key.
Use the V or v key to select a menu, then press the b or ENTER key. The selected menu appears.
Menus Setting items
About the memory of the settings
I NPUT�A
3
SET SETT I NG STATU S : ON I NPUT�A : RGB I NPUT�B : RGB LANGUAGE : ENGL I SH I NSTAL LAT I ON : FLOOR�FRONT SPEAKER : ON POWER SAV I NG : OFF S I RCS RECE I VER : FRONT&REAR
The settings are automatically stored in the projector memory.
Unplug the AC power cord from the wall outlet after the fan stops running and the STANDBY indicator lights in red.
When no signal is input
When there is no input signal, �NO INPUT-Cannot adjust this item.� appears on the screen, and each item cannot be adjusted.
3
Make setting or adjustment on an item.
For details on setting individual items, see the relevant menu pages.
When you cannot confirm the on-screen message When you cannot confirm the on-screen message in a certain condition, you can turn off the power by holding the I / u key on the Remote Commander or on the control panel for about one second.
I NPUT SETT I NG
V I DE
O NO I NPU
T
NO I NPUT� Canno t ad j u s t t h i s i t em.
Note
Do not unplug the AC power cord while the fan is still running; otherwise, the fan will stop although the internal heat is still high, leading to breakdown of the projector.
24 (EN)
25 (EN)
1-13 VPL-S900E, VPL-S900M, VPL-S900U
|
|
|
> |
|
