|
Who's Online
There currently are 5991 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The service manual was a copy of the original from Wirlpool. The quality was good, all neccecary information was available including the service-codenumbers, so I could order the right part to be replaced for repair.
Downloding was no probem after the payment.
Thanks for the service!
;
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
;
Service Manual that I received was very helpful to me. Thank you.
;
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
9. Press the MEMORY key to save the data. 10. Similarly, perform steps 1 to 8 with PAL system. 11. Press the MEMORY key to save the data. 3-3-2-2. SUB-CONT, HUE and COLOR (Component) Adjustment 1. Input the 15k Component 100% Color Bars signal to INPUT-A (pin 5), and select the COMPONENT by the INPUT-A of the SET SETTING. 2. Connect an oscilloscope to TP5024 on the C board. 3. Set the COLOR to 0. 4. Enter the RGB-MTRX on the Device adjust of the menu. 5. Select the item of 08 YUV CONT. Adjust the amplitude for 0.63 Vp-p. 6. Set the COLOR to 50. 7. Select the item of 09 YUV COL. Adjust the � or � key so that the right and left bars are equal in level (A portion). 8. Select the item of 02 SUB HUE. Adjust the � or� key so that the two bars in the middle are equal in level (B portion). 9. Press the MEMORY key to save the data.
<15k Component 100% Color Bars Signal>
A B
8. Select the item of 02 SUB HUE. Adjust the � or � key so that the two bars in the middle are equal in level (B portion). 9. Press the MEMORY key to save the data. 10. Switch the format of 1080/60i to GRB output. Select the DTV-GBR by the INPUT-A of the SET SETTING. Similarly, perform steps 2 to 9.
<1080/60i 100% Color Bars Signal>
A
B
3-3-2-4. SUB-CONT, HUE and COLOR (15k RGB) Adjustment 1. Input the 15k RGB 100% Color Bars signal to INPUTA (pin 5), and select the COMPUTER by the INPUTA of the SET SETTING. 2. Connect an oscilloscope to TP5024 on the C board. 3. Set the COLOR to 0. 4. Enter the RGB-MTRX on the Device adjust of the menu. 5. Select the item of 08 YUV CONT. Adjust the amplitude for 0.63 Vp-p. 6. Set the COLOR to 50. 7. Select the item of 09 YUV COL. Adjust the � or � key so that the right and left bars are equal in level (A portion). 8. Select the item of 02 SUB HUE. Adjust the � or � key so that the two bars in the middle are equal in level (B portion). 9. Press the MEMORY key to save the data.
<15k RGB 100% Color Bars Signal>
A
3-3-2-3. SUB-CONT, HUE and COLOR (DTV) Adjustment 1. Input the 1080/60i 100% Color Bars signal to INPUTA (pin 5), and select the DTV-YPbPr by the INPUT-A of the SET SETTING. 2. Connect an oscilloscope to TP5024 on the C board. 3. Set the COLOR to 0. 4. Enter the RGB-MTRX on the Device adjust of the menu. 5. Select the item of 08 YUV CONT. Adjust the amplitude for 0.63 Vp-p. 6. Set the COLOR to 50. 7. Select the item of 09 YUV COL. Adjust the � or � key so that the right and left bars are equal in level (A portion). 3-2
B
VPL-VW10HT
|
|
|
> |
|