|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I BOUGHT A PAIR OF INFINITY VINTAGE SPEAKERS THAT REQUIRED TO BE REPAIRED AND THE ELECTRONIC TECHNICIAN ASKED ME FOR THE SERVICE MANUAL.
I TRIED TO GET IT AT THE MANUFACTURER'S SITE WITH NO SUCCESS, SO I STARTED TO LOOK FOR IT IN THE WEB FOR A LONG TIME, UNTIL I FOUND THE SERVICE MANUAL IN THIS EXCELLENT SITE "OWNER'S MANUAL.COM".
NOW I HAVE MY SPEAKERS WORKING AND ENJOYING THE MUSIC I LIKE.
THANKS TO "OWNER`S MANUAL.COM" I RECOMMEND THIS SITE TO EVERYONE.
;
Very quick response. Very good and accurate print quality of the scanned document.
 ;
The service manual was very usable and clear enough to see the individual values of all of the components (unlike some of the service manuals I have gotten in the past from web sites similar to this one). The price was right and the information was greatly appreciated. It helped me with an otherwise very difficult repair. It was much needed and appreciated. A faster turn around on my order would be nice, but I understand the constraints on your staff's time. Thank you for your service.
;
Excellent manual. Helped me out with disassembling and troubleshooting my projector.
;
thanks you are the best.Very good detail, Quick service response. A useful service manual with all details.
1-12
Projecting Projecting
Rear remote control detector
1 4 5
Front remote control detector ON/STANDBY indicator
COMMAND
OFF ON
4 5
Turn the zoom ring to adjust the size of the picture. Turn the focus ring to adjust the focus.
Note
Do not look into the lens when the projector lamp is on. To Adjust the volume Cut off the sound
I/u
Press the VOLUME +/� keys on the control panel or on the Remoter Commander. the AUDIO MUTING key on the Remote Commander. To restore the sound, press the AUDIO MUTING key again or press the VOLUME + key.
2
INPUT
MUTING
AUDIO PICTURE
LIGHT
VOLUME
I/u
ON /STANDBY
APA
APA
INPUT MENU
POWER SAVING TEMP /FAN LAMP /COVER
APA key
2 3
APA key
MENU LASER
3
Cut off the picture
V B
ENTER
b v
RESET R CLICK
the PICTURE MUTING key on the Remote Commander. To restore the picture, press the PICTURE MUTING key again.
RESET
ENTER
VOLUME
+ �
To get the clearest picture
You can get the suitable picture when a signal from the computer is input. Press the APA key on the Remote Commander or on the control panel. The picture is automatically adjusted to be projected clearest.
1
After all equipment is connected completely, plug the AC power cord into the wall outlet. The ON/STANDBY indicator lights in red and the projector goes into the standby mode.
� Adjust the signal when the still picture is displayed on the screen. � If you switch the input signal or re-connect a computer, press the APA key again to get the suitable picture. � �ADJUSTING� appears on the screen. Press the APA key again during the adjustment to restore the original screen. � �Complete!� appears on the screen when the picture is adjusted properly. The picture may not be adjusted properly depending on the kinds of input signals. � Adjust DOT PHASE in the INPUT SETTING menu when you adjust the picture manually. For details on DOT PHASE, see page 28 (GB).
Notes
2 3
Press the I / u key on the Remote Commander or on the control panel. The ON/STANDBY indicator lights in green. Turn on equipment connected to the projector. Press the INPUT key on the Remote Commander or on the control panel to select the input source. INPUT-A: Selects audio and video signals input from the INPUT A connector. VIDEO: Selects audio and video signals input from the video/audio input connector. (If you connect to both the S VIDEO and VIDEO jacks, the signal from the S VIDEO jack is selected.)
22 (GB)
23 (GB)
|
|
|
> |
|
