|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Manual was complete and available promptly, since I had lost my original manual. Very good response.
;
Whilst this is a photo copy, and some of the pages are a little askew, it was all readable and intact. A real bonus finding an old manual for a classic piece of kit that no other site had.
Great stuff.
;
excellent quality, contains circuits and scan quality, 110 pages
;
It was easy done, and I got exactly what I was looking for.
;
The manuel was exactly what I needed and I received it promptly. Thanks
&
Programming with �VIDEOPlus+�
All the information required for a programming is encoded in the VIDEOPlus+ code.
1 Switch on the TV set. 2 Press the TIMER k button on the remote control. 3 With the digit buttons 0-9 , enter the VIDEOPlus+ code (up to 9 digits) printed in your TV guide next to the
How to programme a recording manually
1 Switch on the TV set. Press the TIMER k button twice. 2 Select a free TIMER block, using the P q or the P r button. Press the TIMER k button.
DATE PROG START V/P END 01 01 20:00 21:30
start time of a TV programme. If you make a mistake, clear with the CLEAR (CL) button.
4 If you want to programme at daily or weekly intervals, press the
vals) or �W-WEEKLY� (weekly intervals) appears in the display. The �daily intervals� function can only be used for recordings to be made from Mondays to Fridays inclusive.
SELECT button until �D-DAILY� (daily inter-
-----------------------NEXT gTIMER CLEAR gCL -/+ 0-9 D/WgSELECT OK 3 With the TIMER k button you select between the entries �DATE� (date), �PROG� (programme number),
5 Confirm the entries with the OK button . The resultant data appears on the TV screen.
Note: If you use VIDEOPlus+ for the first time for this TV channel, the line �SELECT PROG� appears when you confirm the VIDEOPlus+ code. Instead of �E2�, select the programme number for this particular TV channel, using the digit buttons 0-9 and confirm with the OK button. * Switch �VPS� or �PDC� (V/P) on or off with the SELECT button. * If you wish to set a later end time for a recording, press the P q button at step 5 . Each time you press the P q button you will add 15 minutes to the end time. * If e.g.: �20:00� flashes in the display, please set the clock.
6 Finally, press the OK button. Programming is now complete. 4
�START� (start time) and �END� (stop time). You can enter or adjust data, using the P q or the P r button or the digit buttons 0-9 . Confirm each entry with the TIMER k button. You can switch �VPS/PDC� (�V/P�) on and off at step �START� with the SELECT button. You can select between �D� (daily intervals) or �W� (weekly intervals) at step �DATE� with the SELECT button. Finally, press the OK button. Programming is now complete.
5 Make sure that a cassette without erase protection has been loaded. Switch to standby with the STANDBY m button. A programmed recording will only function when the video recorder is switched to standby with the STANDBY m button.
The data has been stored in a TIMER block.
7 Make sure that a cassette without erase protection has been loaded. Switch to standby with the STANDBY m button.
A programmed recording will only function when the video recorder is switched to standby with the STANDBY m button.
Note: * Clear a TIMER-block: After step 1 , select the TIMER block you want to clear with the P q or the P r button. Press the CLEAR (CL) button. * If e.g.: �20:00� flashes in the display, the clock must be set.
|
|
|
> |
|
