|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
5
6
7
8
Step 7: 1st DSP f
CN401 (Pin 20) RESET
j
CN401 (Pin 16)
For the following diagnosis, a digital oscilloscope must be used. SPICLK
A
Is the logic of RST_1 "H" ?
No
Check the output from the DIGITAL MOTHER Assy.
w
Yes R139
Is the clock signal output while the voltage at SPIDS_1 is "L"?
No
Check the output from the DIGITAL MOTHER Assy.
y
Yes R144
Is the logic of RST_1 "H" ? Yes
No
Check the resistors and patterns in the path.
Is the clock signal output while the voltage at SPIDS_1 is "L"?
No
Check the resistors and patterns in the path.
B
Is the logic of RST_1 maintained at "H"? (Does it fall to become "L" periodically?)
k
No It is likely a boot error. (It is very difficult to diagnose which peripheral part of the DSP is in failure.)
Yes CN401 (Pin 19) MOSI
g
Yes R134 REQ_1
Is the clock signal output while the voltage at SPIDS_1 is "L"?
No
Check the output from the DIGITAL MOTHER Assy.
C
z
Does the logic become "H" for a moment when the input stream is changed? No The 1st DSP is in failure. Replace it.
Yes R146
g
Yes CN401 (Pin 21)
Is the clock signal output while the voltage at SPIDS_1 is "L"?
No
Check the resistors and patterns in the path.
AA
Does the logic become "H" for a moment when the input stream is changed? No Check the resistors and patterns in the path.
Yes R142 MISO
h
Yes CN401 (Pin 17) SPIDS_1
Is the clock signal output while the voltage at SPIDS_1 is "L"?
D
No The 1st DSP is in failure. Replace it.
i
Does the logic become "L" for a moment when the input stream is changed? No Check the output from the DIGITAL MOTHER Assy.
Yes CN401 (Pin 18)
x
Yes R137
Is the clock signal output while the voltage at SPIDS_1 is "L"? Yes
No
Check the resistors and patterns in the path.
E
Does the logic become "L" for a moment when the input stream is changed? Yes
No
Check the resistors and patterns in the path.
It is very difficult to diagnose which part is in failure.
F
VSX-94TXH
5 6 7 8
35
|
|
|
> |
|
