|
Who's Online
There currently are 5511 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
Setting Up for Surround Sound
1k
2
125
2.4. Acoustic Cal EQ
16k
Manual [ALL CH ADJ] [FRONT ALIGN] Auto [ALL ADJ & FRONT ALIGN] [Return]
63 500
2 There are two ways to adjust the Acoustic Calibration EQ, MANUAL and AUTO. Use the 5� buttons to select the type of setting you want to use and press ENTER.
MANUAL: Of these manual settings you can choose ALL CH ADJ mode or FRONT ALIGN mode. ALL CH ADJ mode (flat curve): All the speakers are set individually (except for the subwoofer). No special weighting is given to any channel over any other channel so this setting is the most direct representation of the source being played. FRONT ALIGN mode (front speaker curve): All speakers (except for the subwoofer) are set in accordance with the settings of the FRONT speakers. This setting allows the listener to enjoy a sound balance defined by the front speakers (the main
Your Speaker Systems � Normal Surround �
125
Please Wait Caution!! Test tone is output loudly. [Cancel]
3
2.4. Acoustic Cal EQ Manual Target Curve: ALL CH ADJ Channel [FL �SMALL] 2.4. Acoustic Cal EQ Manual Target Curve:Front ALIGN Channel [FL �SMALL]
16k
2.4. Acoustic Cal EQ Manual
4k
2k
speakers for home theater). AUTO: The frequency balance is set automatically by the receiver (see page 15) and both types of manual calibration are adjusted this way.
WARNING : Be prepared! The test tones are output at a high volume level.
63
250 500
2k 4k 8k
63
250 500 1k
[Return]
This Channel No Adjust [Return]
4
2.4. Acoustic Cal EQ Manual Target Curve: ALL CH ADJ Channel [FL �SMALL]
4k 8k
3 If you're using a MANUAL setting, use the 2 3 buttons to select the speaker and press ENTER.
If you have selected the FRONT ALIGN mode, you can�t set the frequency for the front left and right speakers.
[Return]
6
2.4. Acoustic Cal EQ Manual Channel [FL �SMALL]
Target Curve: ALL CH ADJ
4 Use the 2 3 buttons to select the frequency and 5� buttons to add or subtract decibels from that frequency.
Changing the frequency balance of one channel too drastically will result in a poor overall level balance. You can adjust the speaker levels using the WIDE feature, which allows you to align the speaker level while listening to the test tone. To use the WIDE feature, use 3 to move to the far right side of the OSD then use � and 5 to raise or lower the level of that channel.
1k 2k
[Return]
8k 16k
125 250
memo
The message EQ GAIN OVER indicates there is a possibility the sound will distort due to an extreme frequency balance. If this message appears, adjust the frequency balance accordingly.
5 When you have the frequency balance you want for that speaker press ENTER to move to the next speaker and repeat step 3. 6 Select RETURN with the 5� buttons when done and press ENTER.
You will return to the SURROUND SETUP menu. If you want to proceed to CHECK THE AUTO SETTINGS select RETURN and press ENTER. If you want exit the setup process select EXIT and press ENTER.
46
En
|
|
|
> |
|