|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Manual is in German but complete. I needed this one to fix a long lasting problem with the internal PSU of the camera. Most of the capacitors begin to leak after a few years wich results in the inability to power on the camera. When you try to turn it on the power led flickers and the unit directly turns off. Thanks to this manual I was able to locate all bad cap's and to dis- and reassemble the camera without any problems.
 ;
We received the manual in a timely manner and it was exactly what we were expecting.
;
Excellant, finally this is want I need and searching for The service manual is fantastic and thank you to owner-manuals.com and its service. Price is reasonable. It's a bit slow on my end in downloading but manage to receive the whole manual without a break. once again, thanks.
;
Very good scanning quality. All schematics are very legible. Worth every cent !
;
Excellent quality, very quick download turnaround, will definately use again.
5
6
7
8
A M
IC152 (pins 2, 5) DDC_RX1
Q
IC101 (pins 58, 59, 62, 63, 66, 67, 70, 71) TMDS_RX2
A
Are signals detected?
No
Check the soldering of CN101. If soldering has not been done correctly, replace CN101.
Do signals (approx. 0.5 Vp-p) run in all the lines?
No
Check the soldering of CN102. If soldering has not been done correctly, replace CN102.
M
Yes
IC152 (pins 3, 6) Are signals the same as those at Pins 2 and 5 detected ? N Yes Q153 (pins 1, 4) Are signals the same as those at Pins No 6 and 3 but whose voltage has been converted from 5V to 3V detected? Yes
R
Yes DDC_RX2 No Check the soldering of CN102. If soldering has not been done correctly, replace CN102.
B
IC172 (pins 2, 5) No Check the soldering of IC152. If soldering has not been done correctly, replace IC152.
Are signals detected?
R
Yes
IC172 (pins 3, 6) Are signals the same as those at Pins 2 and 5 detected ? Check the soldering of IC172. If soldering has not been done correctly, replace IC172.
C
Check the soldering of Q153. If soldering has not been done correctly, replace Q153.
No
S
Yes
O
IC161 (pins 2, 15) Are signals the same as those at Pins 3 and 13 detected immediately after the power is turned on? Yes IC151 (pin 8) No Check the soldering of D151. If soldering has not been done correctly, replace D151.
Q173 (pins 1, 4) Are signals the same as those at Pins 6 and 3 but whose voltage has been converted from 5V to 3V detected? Yes
No
No Check the soldering of IC161. If soldering has not been done correctly, replace IC161.
Check the soldering of Q173. If soldering has not been done correctly, replace Q173.
P
O
IC161 (pins 4, 11)
D
Is the voltage about 5V? Yes
Are signals the same as those at Pins 3 and 13 detected immediately after the power is turned on?
No Check the soldering of IC161. If soldering has not been done correctly, replace IC161.
Check the soldering of IC151. If soldering has not been done correctly, replace IC151.
T
Yes IC171 (pin 8)
Is the voltage about 5V? Yes Replace IC171
No
Check the soldering of D171. If soldering has not been done correctly, replace D171.
E
F
VSX-AX4AVi-S
5 6 7 8
213
|
|
|
> |
|
