|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
As Always you can find here manuals even of difficult TV scheme which are scan in almost perfect way.clear and fast!!!!!
Great work thanks!
 ;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
 ;
again you did a very good job. It was fast too. Photocopy are really readable and clear
 ;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
5
6
7
8
A M
IC152 (pins 2, 5) DDC_RX1
Q
IC101 (pins 58, 59, 62, 63, 66, 67, 70, 71) TMDS_RX2
A
Are signals detected?
No
Check the soldering of CN101. If soldering has not been done correctly, replace CN101.
Do signals (approx. 0.5 Vp-p) run in all the lines?
No
Check the soldering of CN102. If soldering has not been done correctly, replace CN102.
M
Yes
IC152 (pins 3, 6) Are signals the same as those at Pins 2 and 5 detected ? N Yes Q153 (pins 1, 4) Are signals the same as those at Pins No 6 and 3 but whose voltage has been converted from 5V to 3V detected? Yes
R
Yes DDC_RX2 No Check the soldering of CN102. If soldering has not been done correctly, replace CN102.
B
IC172 (pins 2, 5) No Check the soldering of IC152. If soldering has not been done correctly, replace IC152.
Are signals detected?
R
Yes
IC172 (pins 3, 6) Are signals the same as those at Pins 2 and 5 detected ? Check the soldering of IC172. If soldering has not been done correctly, replace IC172.
C
Check the soldering of Q153. If soldering has not been done correctly, replace Q153.
No
S
Yes
O
IC161 (pins 2, 15) Are signals the same as those at Pins 3 and 13 detected immediately after the power is turned on? Yes IC151 (pin 8) No Check the soldering of D151. If soldering has not been done correctly, replace D151.
Q173 (pins 1, 4) Are signals the same as those at Pins 6 and 3 but whose voltage has been converted from 5V to 3V detected? Yes
No
No Check the soldering of IC161. If soldering has not been done correctly, replace IC161.
Check the soldering of Q173. If soldering has not been done correctly, replace Q173.
P
O
IC161 (pins 4, 11)
D
Is the voltage about 5V? Yes
Are signals the same as those at Pins 3 and 13 detected immediately after the power is turned on?
No Check the soldering of IC161. If soldering has not been done correctly, replace IC161.
Check the soldering of IC151. If soldering has not been done correctly, replace IC151.
T
Yes IC171 (pin 8)
Is the voltage about 5V? Yes Replace IC171
No
Check the soldering of D171. If soldering has not been done correctly, replace D171.
E
F
VSX-AX4AVi-S
5 6 7 8
213
|
|
 |
> |
|