|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
11
Additional information
Symptom
No sound from subwoofer.
Cause
Remedy
� The subwoofer is disconnected or switched � Connect or switch on the subwoofer (see page 13). off. � The subwoofer's settings are incorrect. � The subwoofer's levels are too low. � The LFE Attenuator is set to OFF. � Set the subwoofer (see page 31). � Set the front speakers to Small (S) (see page 31). � See on page 33 to check the speaker levels. � Set the LFE Attenuator to either 0 dB or 10 dB (see page 32).
When a search is performed by a � The search function performed by the player � This is not a malfunction, but be sure to turn the volume DTS compatible CD player slightly alters the digital information, making down to prevent the output of loud noise from your during playback, noise is output. it unreadable. speakers. The Dolby/DTS indicator doesn't light when playing Dolby/DTS software. � The player is paused. � The player's sound output settings are wrong. � Press play. � Set the player correctly (consult the manual that came with the player, if necessary). � Turn the volume down. � Turn on input attenuator (see page 32). � Turn the volume down. � Set the front speakers to large (L) (see page 31).
When playing a 96 kHz/24bit disc � Different discs have different recording the sound is too loud. levels so some may be louder than others. The sound distorts. You can only hear treble from speakers. � The analog signal is too strong. � Master volume is too loud. � The front speakers are set to small (S).
Sound is produced from analog � Digital connections are incorrect. � Make digital connections (see page 8) components, but not from digital � The digital output of the player is turned off. � Turn on the digital output of the player on (consult the ones (DVD, LD, CD-ROM etc.). manual that came with the player, if necessary). � The CD-ROM player is outputting a data stream (not an audio signal) which is incompatible with this receiver. � Digital connections are incorrect. � Analog input has been selected. � The digital input assignment is wrong. No sound is output or a noise is output when Dolby Digital/DTS software is played back. � Use a player that is compatible with this receiver.
� Make digital connections (see page 8). � Select digital input (see page 29). � Assign the digital input (see page 32).
� A DVD player not compatible with Dolby � Make sure your DVD player is compatible with Dolby Digital/DTS is being used. Digital/DTS. � The settings on the DVD player are incorrect � Make sure the player's settings are correct and/or the and/or the DTS signal output is turned off. DTS signal out is on. Refer to the instruction manual supplied with the DVD player.
� The digital output level is turned down on a � Set the digital volume level of the player to full, or to the CD player or other component equipped with neutral position. digital output level adjustment capability. (The DTS signal has been altered by the player, and cannot be read.) The settings have all been cleared. No image is output when an input is selected. � The receiver has been unplugged or the � Set the receiver again (see page 31). main power turned off for more than a month. � The video connections are incorrect. � The input source is not properly selected. � Make sure the video component is connected correctly (see page 12). � Make sure the proper component is selected by pressing the correct function button (see page 22).
� The DVD/video player settings are incorrect. � Set correctly. Refer to the instruction manual supplied with the DVD/video player. The settings have all been cleared. � The receiver has been unplugged or the � Set the receiver again (see page 31). main power turned off for more than a month. � Make sure there are no loose strands of speaker wire touching the metal casing of the receiver. � Turn the volume down.
OVERLOAD blinks in the display � The speaker cable is shorting out the unit. and the power turns off automatically. � The output is too high. You can't set the subwoofer frequency crossover. The display is dark or off. After making an adjustment the display goes off.
� All the speakers are set to either large (L) or � Change the speaker settings (see page 31). �� (i.e. no speakers are set to small). � The display is set to dark or off. � The display is set to off. � Press DIMMER on the remote control repeatedly to select a different brightness. � Press DIMMER on the remote control repeatedly to select a different brightness.
40
En
|
|
|
> |
|
