|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
perfect! you just sent to me the copy in Italian witout even my specification!!!! so you are really smart cooperative and efficient. To my opinion the best place all over to get a manual of electronics!!!!
;
Well Well Well!!!! Good manual perfect for my hobby!!! As Before you have done a very well done work!!!! Thank you
;
Super nice! Good to have a manual in digital format.
;
Great job supplying the manual.
Many of these products weerepretty obscure, so it was great that you had
the manual for it!
;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
Fine Tuning Your System
For explanation purposes the illustrations use ALL CH ADJUST. This explanation is for CUSTOM 1 or CUSTOM 2.
1
Acoustic Cal EQ [ CUSTOM1 ADJUST [ CUSTOM2 ADJUST [ DATA COPY [ DATA CHECK [Exit ] ] ] ] ]
1 The four possibilities should be on the OSD. Use the 5� buttons to select CUSTOM 1 or CUSTOM 2. Press ENTER. 2 Use the 5� buttons to select ALL CH ADJUST or FRONT ALIGN and press ENTER.
The test tones will sound.
2
Acoustic Cal EQ [ ALL CH ADJUST ] [ FRONT ALIGN ] [Exit ]
WARNING: the test tones are very loud!! Make sure there are no infants or small children in the room and that no one who will be scared, upset or damaged by loud noise is present. You yourself may want to wear earplugs. Here the terms ALL CH ADJUST and FRONT ALIGN represent two types of equalizer methods that emphasize different characteristics of the sound. ALL CH ADJUST: In this method all the speakers (except for the subwoofer) are independent. The settings that were input when you did the AUTO SURROUND SOUND SETUP (see pages 13-15) will be present but you can adjust each speaker individually to suit your taste. The test tones for each channel will sound individually. FRONT ALIGN: In this method all speakers (except for the subwoofer) are set in accordance with the settings of the FRONT speakers. The settings that were input when you did the AUTO SURROUND SOUND SETUP (see pages 13-15) will be present but you can adjust each speaker individually to suit your taste. This setting allows the listener to enjoy a sound balance defined by the front speakers. The front left speaker will serve as the reference tone. The front left tone and the target speaker (the one you are trying to adjust) will sound in turns, so you can judge which needs to be louder.
3
ALL CH ADJUST [ Front L [ Center [ Front R [ Surround [ SurrBack [ SurrBack [ Surround [Exit ] EQ ] EQ ] EQ ] EQ ] EQ ] EQ ] EQ ]
R R L L
4
Center EQ 63Hz 125Hz 250Hz 4 kHz 11.3 kHz TRIM [Exit] [ [ [ [ [ [
+1. 5dB ] +2. 5dB ] -4. 0dB ] -5. 5dB ] +0. 5dB ] +0. 0dB ]
3 Use the 5� buttons to select the channel that you want to adjust. Press ENTER.
5
Center EQ 63Hz 125Hz 250Hz 4 kHz 11.3 kHz TRIM [Exit] [ [ [ [ [ [
+2. +2. -4. -5. +0. +0.
0dB ] 5dB ] 0dB ] 5dB ] 5dB ] 0dB ]
For FRONT ALIGN you won't be able to adjust the FRONT speakers.
4 Use the 5� buttons to select the frequency you want to adjust. Press
ENTER.
For the speakers you set to SMALL (see page 41) you won't be able to adjust the 63 Hz setting.
5 Use the 5� buttons to adjust the frequency. When you have it at the level you want press ENTER.
Set the frequencies within the �6 dB to +6 dB range in steps of 0.5 dB. If OVER appears in the display you have set the levels too high. Reduce them until OVER disappears.
100
En
6 The cursor automatically goes to the next frequency. Press ENTER and repeat steps 4 & 5 to adjust all the frequencies.
|
|
|
> |
|
