|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellant!!! Very quick and easy....Best $4.99 I have spent in a very long time..
I highly recommend this.
;
Thanks so much for the Owner's manual for my Sony PS - FL1. I had purchased the turntable off of eBay. It came in and looked great. Packed well and appeared to be great. I balanced and aligned the tone are and hooked it up. When trying to play a record the tone are would move to the right place and just before it would drop to play it moved back off the edge of the record before touching down. I searched the net for an answer to this issue. No luck. Then I purchased the owners manual and sure enough there was a place to adjust where the stylus touched down. That adjustment solved the problem and saved me a $35 feet to have the player checked out. The manual is well written and easy to understand. It is a must have for anyone with this front loading Sony turntable.
;
Some years back I pruchased a Sansui G-9000. I had it cleaned up and a problem with the left channel repaired. When I got it back I hooked it up to my tape decks, turn tables, TV and it played great. The only thing I was not really satisfied with was the performance of my Graphic Equalizer. I purchased this owner's manual had poured myself a cup of coffee. The manual is well organized and written in plain language. It also contained the solution to my dissatisfaction. By using the preamp connections coupled I was able to run everything through my graphic equalizer and now enjoy the full potential of my complete system.
 ;
An excellent service for the price, however, it would also have been handy if the troubleshooter pages were included. The manual is only sent in the language of your country, thus it looks as though there are some pages missing. Otherwise highly recommended.
;
I am happy to get a rare TECHNICS SH-9090 Owner's Manual by PDF in clear copy.
Controlling the rest of your system
10
3 Use the number buttons to enter the preset code. You can find the preset codes on page 64 (VSX-D712) and page 65 (VSX-D812/912). The LED blinks again after you enter the code. If the correct code has been input the power of the component being input will turn on or off. The power of the component being input will only turn on or off if that component is able to be turned on directly by remote control. � You can only input a code for the component type written on each MULTI CONTROL button (except RECEIVER and TUNER). � Even if you don�t input a preset code for the TV (TV/SAT MULTI CONTROL button) you will be able to control your TV using the dedicated TV CONTROL on the remote if you have assigned it to the TV CONT button. � You may not be able to use a particular code even if it is listed on page 64. � The remote control buttons will not be able operate other equipment unless preset with the method above. 4 Repeat steps 2 through 3 to try a different code, or to enter a code for another component you want to control. 5 When you�re done, press RECEIVER.
nent (for example , , or other operation buttons). This can also be used to program additional operations (buttons not covered in the presets) after assigning a preset code. 1 While pressing the RECEIVER button, press and hold the 2 button. The LED blinks. 2 Press the MULTI CONTROL button for the component you want to control. The LED lights. � To exit or cancel press RECEIVER. 3 Point the two remote controls towards each other about 2�5 cm apart then press the button that will be doing the learning on this receiver�s remote control. The LED blinks rapidly.
2 � 5 cm
4 Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver�s remote control. If the operation has been learned successfully, the LED on this receiver�s remote will blink once then light steadily. If for some reason the operation hasn�t been learned the LED will blink for three seconds and then light steadily. If this happens, keep pressing the (teaching) button as you vary the distance between the two remotes, until you see the the LED light steadily. If there is not enough memory for this button to be learned by the remote, the LED will blink twice and the operation will be canceled. 5 To program additional signals for the current component repeat steps 3 and 4. To program operations for another component exit and repeat steps 1 through 5.
English Italiano Français Deutsch Nederlands Español
Programming signals from other remote controls
VSX-D812/D912 only If the preset code for your component is not available, or the available preset codes do not operate correctly, you can program signals from the remote control of another compo-
59
En
|
|
|
> |
|
