|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
good and ok, very nice , good and ok, very nice, good and ok, very nice
;
Super manual it contains all the things you need to service your Marantz 2100.
;
A very easy to understand and use manual. Well worth the money.
 ;
Very good information with clear drawings. Thanks!
;
The ease of this purchase was a good start. The content of this manual was exactly all I needed to retore my Tandberg 64.
All of the mechanical and electrical information is contained in the manual and the quality of the document makes reading the data easy.
The exerience with the resource has made this my prime source for technical data.
ELECTRICAL ADJUSTMENTS
2-10: CUT OFF 1. Set condition is AV MODE without signal. 2. Using the remote control, set the brightness and contrast to normal position. 3. Place the set with Aging Test for more than 15 minutes. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (00) on the remote control to select "CUT OFF". 5. Adjust the Screen Volume until a dim raster is obtained. 2-11: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "R DRIVE". 5. Press the LEFT/RIGHT button on the remote control to select the "R DRIVE", "G DRIVE", "M R CUT OFF" or "M G CUT OFF". 6. Adjust the LEFT/RIGHT button on the remote control to whiten the R DRIVE, G DRIVE, M R CUT OFF, and M G CUT OFF at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is looked like a white. 2-12: BRIGHT CENT 1. Receive the PAL black pattern*. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "BRIGHT CENT". 4. Press the LEFT/RIGHT button on the remote control until the screen begin to shine. 5. Receive the PAL black pattern*. (Audio Video Input) 6. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 7. Press the DVD button on the remote control to set to the DVD mode. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "BRIGHT CENT". 9. Press the LEFT/RIGHT button on the remote control to set the same step numbers as the AV mode. *The Black Pattern means the whole black raster signal. Select the "RASTER" of the pattern generator, set to the OFF position for each R, G and B. Fig. 2-2 2-13: CONTRAST CENT 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "CONT CENT". 2. Press the LEFT/RIGHT button on the remote control until the contrast step No. becomes "30". 3. Receive a broadcast and check if the picture is normal. 4. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the DVD button on the remote control to set to the DVD mode. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "CONT CENT". 7. Press the LEFT/RIGHT button on the remote control to set the same step numbers as the AV mode. 2-14: COLOR CENT 1. Receive the PAL color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast and color to normal position. 3. Connect the oscilloscope to TP803. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (25) on the remote control to select "COLOR CENT". 5. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 6. Press the LEFT/RIGHT button on the remote control until the red color level is adjusted to 90 ± 10% of the white level. (Refer to Fig. 2-2) 7. Receive the PAL color bar pattern. (Audio Video Input) 8. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~6. 9. Press the DVD button on the remote control to set to the DVD mode. 10. Activate the adjustment mode display of Fig. 1-1 and press the channel button (25) on the remote control to select "COLOR CENT". 11. Press the LEFT/RIGHT button on the remote control to set the same step numbers as the AV mode.
90%
100%
D-3
|
|
|
> |
|
