|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
;
excellent value & price! Includes everything you need to know about the NN-C777! I would buy this again.
;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
;
I purchased the unit from a private party and the original owners manual was not available. Having the ability to download it was extremely helpful and clarified operating the equipment immensely. This is a complicated unit and without the manual I would not have been able to maximize it's potential. Thank you.
4GB05129.FM Page 15 Tuesday, March 2, 2004 5:08 PM
a. Fault in the water supply The appliance has no or insufficient water supply. For models with a fault display, the �Water tap� lamp lights up and (depending on model) the spin speed indication lamps flash. For models with no fault display, the washing machine stops in the appropriate programme step. Switch the appliance off and pull out the mains plug. Check whether: � the water tap is fully turned on, and the water supply pressure is sufficient � the water inlet hose is kinked � the water connection mesh filters are blocked (see �Care And Maintenance�/�Mesh Filters in the Water Connection�) � the water supply hose is frozen up � the washing machine has a safety hose and the safety valve is open (red indicator in the safety valve inspection window); In this case replace it with a new safety hose Reconnect the appliance to the electrical socket. For models with a fault display, reselect the desired programme and start it. For models without a fault display continue the programme by pressing the �On/Off� or the �Start� or the �Start/Pause� button (depending on model) again. If the fault occurs again, please contact After-Sales Service (see �After-Sales Service�). b. Draining fault Waste water not pumped out. For models with a fault display the spin speed indication lamps flash and the pump display flashes. If a digital display is fitted, �P� and �F� are also displayed alternately. For models with no fault display, the washing machine stops in the appropriate programme step. Switch the appliance off and pull out the mains plug. Check whether: � the drain hose is kinked � the pump or the filter is blocked (see �Removing The Filter�) IMPORTANT: before draining, make sure that the water has cooled down. � The water in the drain hose is frozen up Reconnect the appliance to the electrical socket. For models with fault display, select and start the �Drain� cycle. To rinse the laundry, we then recommend a short programme without the addition of detergent. For models without a fault display continue the programme by pressing the �On/Off� button again. If the fault occurs again, please contact After-Sales Service (see �After-Sales Service�). c. Fault in an electrical component The appliance stops in the middle of a programme. For models with a fault display, the spin speed indication lamps flash. If a digital display is fitted, �F4� to �F16� are also displayed. Switch the washing machine off. First of all select and start the �Drain� cycle.
Then select and start the desired programme again. For models with no fault display, the washing machine stops in the appropriate programme step. First switch the washing machine off and on again to continue with the programme. If the fault persists, please contact After-Sales Service (see �After-Sales Service�). d. �Water Stop� fault (if fitted) The �Water Stop� fault may have been triggered by: 1. excess foaming 2. a leak in the washing machine. In this case the pump is switched on automatically in order to pump the water out. For models with a fault display, the �Water Stop� indication flashes and the spin speed indication lamps flash. If a digital display is fitted, �A� and �F� are also displayed alternately. For models with no fault display, the washing machine stops in the appropriate programme step. Switch the appliance off, pull out the mains plug and turn the water tap off. Tilt the appliance forwards ( with 2 people it is suggested), to allow the collected water to flow out from the bottom of the appliance. Then: 1. Plug in the appliance. 2. Turn the water tap on (if water immediately flows into
the appliance again, without the appliance being started, there is a fault. Turn off the tap and notify After-Sales Service). 3. For models with fault display, select and start the desired programme again. For models with no fault display, continue the programme by pressing the �On/Off� button again.
If the fault occurs again, please contact After-Sales Service (see �After-Sales Service�).
15
Black process 45.0° 100.0 LPI
|
|
|
> |
|
