|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
;
This is a great manual. It was easy to read and very accurate. The size of the manual is small so email is no problem. I highly recommend it. The manual is very hard to find other than this website.
;
Manual was complete and available promptly, since I had lost my original manual. Very good response.
REC ONLY: Only alarm recording will start and monitors will keep displaying the current sequence/spot images. Note: You cannot recover alarm-related operations from system controllers when REC ONLY is selected. OFF: An alarm input is not accepted via the ALARM port. The factory default setting is ON. Each alarm input's polarity is configurable in the submenu. Set ALARM PORT to ON or REC ONLY, and press the CAM (SET) button. 440 ALARM INPUT (ALARM PORT) will appear on the monitor.
440 ALARM INPUT(ALARM PORT) SWITCHER=SLAVE1(1 of 5) 1 2 3 4 5 6 7 8 NORMALLY NORMALLY NORMALLY NORMALLY NORMALLY NORMALLY NORMALLY NORMALLY OPEN CLOSE OPEN OPEN CLOSE OPEN OPEN OPEN 9 10 11 12 13 14 15 16 NORMALLY OPEN NORMALLY OPEN NORMALLY OPEN NORMALLY OPEN NORMALLY OPEN NORMALLY OPEN NORMALLY OPEN TIME ADJUST
Note: You cannot recover alarm-related operations from system controllers when REC ONLY is selected. OFF: An alarm input is not accepted via the SERIAL port. The factory default setting is ON. 460 MUX MOTION DET MUX This stands for that the unit�s motion detector is activated when a camera detects the brightness-level change and transmit an alarm signal. ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start (if a recorder is connected to the unit.) REC ONLY: Only alarm recording will start and monitors will keep displaying the current sequence/spot images. Notes: � If the Multiplexer board is not installed in the unit, you cannot enter the submenu of 460 MUX MOTION DET. � You cannot recover alarm-related operations from system controllers when REC ONLY is selected. OFF: An alarm input is not accepted by the motion detector.
Move the cursor and press the CAM (SET) button to go into the menu. SWITCHER: Select a unit (SLAVE1 to 4 and MASTER*) to configure the parameters. * In normal connection, only MASTER is displayed. After designating the unit, select the desired polarity for ALARM 1 to 16. NORMALLY OPEN: Normally Open contact is activated for the alarm input signal. NORMALLY CLOSE: Normally Close contact is activated for the alarm input signal. TIME ADJUST: This polarity enables the input of the time adjusting signal. The factory default setting is N. O.
To configure where to activate the motion detector, set MUX MOTION DET to ON or REC ONLY, and press the CAM (SET) button. The live image will be displayed. Up to 4 motion-detection areas are configured for each camera channel. Note: Black image will be displayed on the monitor if the currently selected channel has no camera connection. A �+� mark appears at the center of the monitor.
Logical camera number and sensitivity C01 LOW
+
Note: In the master-slave connection, time setting of every unit can be synchronized when the time adjusting signal is input to any unit. 450 SERIAL PORT This stands for that an alarm input is accepted via the SERIAL port. ON: The alarm-associated sequence/spot image is displayed on a monitor, and alarm recording will start (if a recorder is connected to the unit.) REC ONLY: Only alarm recording will start and monitors will keep displaying the current sequence/spot images.
Mark
The following is the setting procedure.
69
|
|
|
> |
|
