|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
 ;
The manual was exactly what I needed, Good quality scans too. superb.
;
El producto satisface las necesidades del servicio t
;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
(7) Check first that indication �L� of �AC1L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). n If the �L� indication does not disappear from the LCD (on A area: refer to the previous procedure (5) (when the RF input level is lower than the reference level) or �H� is displayed (when the RF input level is higher than the reference level), perform the following adjustment. 1 Check the RF output level and frequency of the signal generator (perform re-setting if necessary), and repeat from procedure (1). 2 If the above conditions (the �L� indication does not disappear, or �H� is displayed) remain even after re-adjustment, it is necessary to check the WRU-806A Tuner Unit. (8) Indication on the LCD (Tuner [1]) appears as follows: LCD:
(13)Check first that indication �L� of �AC3L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (14)Connect the signal generator to the ANTENNA B IN connector with DC cut fixture. (15)Indication on LCD (Tuner [1]) appears as follows: LCD:
B C1 L
(B C1 L)
A C2 L
(A C2 L)
(16)Set the FREQUENCY(carrier frequency) of the signal generator as follows; FREQUENCY(carrier frequency): U64 model; 772.000 MHz U66 model; 784.000 MHz U68 model; 796.000 MHz (17)Check first that indication �L� of �BC1L� on the LCD has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (18)Indication on the LCD (Tuner [1]) appears as follows: LCD:
(9) Set the FREQUENCY (carrier frequency) of the signal generator as follow. FREQUENCY(carrier frequency): U64 model; 776.000 MHz U66 model; 788.000 MHz U68 model; 800.000 MHz (10)Check first that indication �L� of �AC2L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (11)Indication on the LCD (Tuner [1]) appears as follows: LCD:
B C2 L
(B C2 L)
A C3 L
(A C3 L)
(19)Set the FREQUENCY(carrier frequency) of the signal generator as follows; FREQUENCY(carrier frequency): U64 model; 776.000 MHz U66 model; 788.000 MHz U68 model; 800.000 MHz (20)Check first that indication �L� of �BC2L� on the LCD (Tuner [1]) has disappeared, and then press the S708 switch on the RF-92 board (WRU-806A, Tuner [1]). (21)Indication on the LCD (Tuner [1]) appears as follows: LCD:
(12)Set the FREQUENCY (carrier frequency) of the signal generator as follow. FREQUENCY(carrier frequency): U64 model; 780.000 MHz U66 model; 792.000 MHz U68 model; 804.000 MHz
B C3 L
(B C3 L)
3-4
MB-806A (U) WRU-806A (U)
|
|
|
> |
|
