|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
 ;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
;
has all the schematics you could need,and very well laid out format also has all part numbers along with an exploded view which is helpful
;
Very nice to have! Now it is no problem to understand how it is put together.
Helps me a lot.
;
good scans, all is clear. all pages in order. recommended
XAV-A1
2 Installing the Main Unit
Installation angle
The unit should be installed within an angle of 30 degrees from horizontal. If this angle is exceeded, the monitor may not open up or retract properly.
Installation procedure
Mounting example When installing this unit, be sure to close the monitor of the unit. If the monitor is opened while installing and given too much force, it may cause a malfunction.
After all connections are made, install the main unit to the dashboard.
Before installation
1
This unit is designed to be completely safe, but if not installed correctly, it can cause accidents. Be sure to verify the following points before installation. Install the main unit to the in-dash location, and the amplifier unit under the navigator�s seat, etc. � If the monitor in the opened position is close to a airconditioning outlet, the outlet should be closed. � Install the unit so that the monitor when opened up will not block access to the hazard switch or other important controls. � Do not install the unit (monitor) in locations which may be subject to excessively low or high temperatures. (Otherwise the unit may be deformed and the LCD may be damaged.) Exposure to direct sunlight can also lead to high temperatures and should be avoided.
Note
Keep the units and connection cables apart.
182 m m
53 mm
0
2
Selecting the installation location
1 2
Set the ignition key to OFF or remove it. Place the units in their intended mounting locations to check the cable length and monitor installation conditions.
Claws
3
(US, Canadian) Dashboard
Installation procedure precautions
� Perform the installation carefully. Dropping the unit or otherwise subjecting it to strong impact or force may deform the chassis, resulting in failure of the monitor loading mechanism or other defects.
T T N N
0
qa
N T/N T
T/N T/N
� To allow for proper opening and closing of the monitor, there must be a clearance of at least 170 mm between the closest position of the shift lever and the mounting surface for the unit.
(Except US, Canadian) Dashboard
Fire wall
8 Shift lever At least 170 mm from mounting surface
9
� In some cases, the shift lever may touch the monitor when moved to a certain position. Make sure that there is no obstruction to driving operations. � When installing this unit together with other car audio equipment (single DIN slot size) in a stacked configuration, install the main unit on top.
qa
qs
11
12
Toyota cars (illustration shows an example for a Toyota car) Align the brackets of the factory-installed car stereo with the mounting holes marked �T� on the side of the main unit, and use the supplied screws to fasten the brackets. For Toyota cars, the supplied screws 6 should be used.
6 XAV-A1 Bracket of factory-installed car stereo
3 After Installation and Connections
1
Start the car�s engine.
2 Verify that and brake lights, other parts operateturn the lights, horn, indicators, all other electrical
normally.
Note
3 Use a mechanical-pencil or similar to push the Reset
button on the unit.
Notes
� Do not press the front panel buttons of the unit during installation and do not apply strong force. � Do not place any objects on top of the unit. � If a salient of the genuine bracket touches the unit due to its figure, and makes attachment hard, process the bracket by scraping the salient off.
To avoid the possibility of damage, you should not use a needle or push the button too strongly. Screws of factoryinstalled car stereo bracket
Nissan cars Align the brackets of the factory-installed car stereo with the mounting holes marked �N� on the side of the main unit, and use the supplied pan-head screws 6 to fasten the brackets.
6 XAV-A1 Bracket of factory-installed car stereo
When you press the Reset button, the system becomes operative.
Reset button
Screws of factoryinstalled car stereo bracket
* Be sure to use only the supplied pan-head screws 6 for installation. If any other screws are used, make sure they conform to the requirements shown below. Using longer screws can cause internal damage to the unit.
5 mm
6 mm
Damage can also occur if the screws are used directly on the unit without the brackets of the factory-installed car stereo.
13
14
12
|
|
|
> |
|
