|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
- CONTENTS/ACCESSORIES
- EXTERNAL VIEW
- DISASSEMBLY FOR REPAIR
- BLOCK DIAGRAM
- CIRCUIT DESCRIPTION
- ADJUSTMENT
- WIRING DIAGRAM
- WIRING DIAGRAM
- PC BOARD
- SCHEMATIC DIAGRAM
- EXPLODED VIEW
- PARTS LIST
- SPECIFICATIONS
There are currently no product reviews.
 ;
Even if the PDF is a scan, I can read the information I need.
The price is affordable and the service (mail sending) is very fast.
Thanks ! Regards. William (Fan of Kenwood)
;
Very good quality original datasheet!I like this amazing website!!!!!!
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
RXD-501/551/571/A5/701/751/771/A8
ADJUSTMENT
5. Cassette Deck adjustment
No ITEM INPUT SETTING OUTPUT SETTING DECK SETTING ALIGNMENT POINT ALIGN FOR FIG.
Unless otherwise specified, set the respective switches as follows: TAPE : NORMAL DOLBY : OFF PLAY OUT : Lch (X28,CN6 1pin), Rch (X28,CN6 4pin) ø. Cassette mechanism unit (Adjustment of the REC / PLAY head)
0dBs=0.775V
<1>
Demagnetization and cleaning
�
�
Power : OFF Demagnetization,cleaning, PLAY
Demagnetize the REC / PLAY head with the head erasRecording er.Clean the REC / head, erase PLAY head, erase head,capstan head,capstan and pinch roller pinch roller using a cotton swab slightly damped with alcohol. Adjust the output to maximum and adjust the azimuth adjustment screw for the Lissajours waveform pattern of the oscilloRVS scope to become close to a 45° straight line.
<2>
Azimuth of the REC/PLAY head
TCC�153 MTT�114 10kHz, � 10dB
(B)
PLAY FWD
¿. PC BOARD ADJUSTMENT <1> TAPE SPEED(NORMAL) TCC�110 MTT�111 SCC�1727 3kHz (B) PLAY
{
A DECK VR B DECK 5 VR 6
Adjust the tape speed so that 3kHz is obtained at the center of the tape.
¡. PC BOARD ADJUSTMENT A DECK VR 7 (L) VR 8 (R) B DECK VR 1 (L) VR 2 (R)
<1>
PLAYBACK LEVEL
MTT� 150 400Hz
(B)
PLAY
Adjust the playback output to -2.5dBs
<2>
(A) Adjust the AG for the output of BIAS CURRENT the DECK to become 400Hz (-20dB)/12.5kHz (-20dB)
X28, CN6
1 L IN GND
REC (B)
¤
PLAY
VR 3 (L) VR 4 (R)
Record 400Hz and 12.5kHz alternately, and adjust the bias current adjustment potentiometer for the playback levels to become the same.
L OUT
R OUT R IN 5
AC voltmeter
AG
Oscilloscope
AC voltmeter Frequency counter
(A)
(B)
16
|
|
|
> |
|
