|
Who's Online
There currently are 6031 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
El producto satisface las necesidades del servicio t
;
This is a good quality scan of the Operation & Maintenance (Service) Manual for the PAL version of this high-band broadcast umatic, BVU-800P
All schematics and lineup procedures appear to be included in this one manual AFAICT.
The file size is just over 113 MB which gives an idea of the quality and number of pages.
All of the schematics, which contain some fairly small print, are easily readable when you zoom into the page.
John Thompson, Newcastle Upon Tyne, England.
;
Good quality, all schematics of few of models. There is also short form of user manual and regulation manual.
;
Perfect copy of the service manual. you can enlarge every page, and it comes up
with all details.
;
It´s very very nice manual with all, what i need. Original in good quality. Very fast business. Very much thanks...
3) PRINTER TEST
1 Key operation 102 3 RCPT/PO 2 Test procedure
5) MODE SWITCH TEST
1 Key operation 105 3 RCPT/PO 2 Test procedure
OP display
R/J
PRINTER
PGM
OP display
Enlargement
MODE 105
SW
PGM X
MODE: PGM_VOID_OFF_OP X/Z_REG_MGR_X1/Z1_X2/Z2__PGM X:1 2 9 3 4 5 6 7 1
The above X must be read in the correct order. (If the contact is open, 9 will be displayed.)
5 lines of 24 digits are printed.
3 Check: The display during testing and the content of the completion print.
At the receipt side, the logo is also printed and the receipt is issued. 3 Check that: The print is free from contamination, blur, and uneven density. 4 End of testing The test will end automatically.
4 End of testing When the test ends normally When an error occurs: E�~�
105 105
6) PRINTER SENSOR TEST
1 Key operation 106 3 RCPT/PO 2 Test procedure Check the status of the paper end sensor and head up sensor.
4) KEYBOARD TEST
1 Key operation _ _ _ _104 3 RCPT/PO 2 KEY check sum code 2 Test procedure The keyboard is checked using the sum check code of the key code. If the sum check code is not entered, the check is made using the sum check code of the default keyboard arrangement The sum check data for each model is entered to the front 4 digits of the DIAG code, and that data is compared with the key data added until the final key (CA/AT) is pressed. Both data are the same, the test ends, printing the number given below. If both data are different, the printer prints the error message.
OP display
R/J 106
SENSOR
PGM XY
3 Check the following. X: 1 - Paper present at the receipt side O - No paper at the receipt side Y: 1 - Paper present at the journal side O - No paper at the journal side 4 End of testing
OP display
KEY 104
BOARD
PGM
You can exit the test mode by pressing any key and the printer prints the following.
106
KEY CODE
7) CLOCK TEST
1 Key operation 107 3 RCPT/PO 2 Test procedure
3 Check: A) The content of completion print 4 End of testing When the test ends normally: When an error occurs: Note: Calculation of key sum check data Hard codes (hexadecimal number) at the position (excluding feed key) where there is an input data contact are added. However, the end key (TL) is not added. This data to which hard codes have been added is converted into a decimal number value, which will become the sum check data that will be entered when DIAG is started.
XE-A301V
104
E�~�
OP display
104
T I ME R 104
CHECK
PGM
Hour
Min.
Sec.
Blinks at an interval of 0.5 sec.
3 Check that: ��� blinks and the clock counts up.
DIAGNOSTIC PROGRAM
� 11 �
$4.99 XE-A301 SHARP Parts Catalog Parts Catalog only. It's available in PDF format. Useful, if Your equipment is broken and You need t… $4.99 XE-A301 SHARP Quick Start Quick start guide ( sometimes called quick guide ) contains most important information on how to use…
|
|
|
> |
|