|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
 ;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
;
The owners manual for the Pioneer VSX-D603S was exactly what I needed. I received it in a timely manor and it was priced fairly. I definately will use your servise again. Thank You
Computer Image Adjustments
Projector
ON MUTE OFF
BLACK SCREEN LASER TOOLS MENU
MOUSE
ADJ.
Saving and Selecting Adjustment Settings
VOL
This projector allows you to store up to seven adjustment settings for use with various computers. Once these settings are stored, they can be easily selected each time you connect the computer to the projector.
1, 6 2, 3, 4 5
R-CLICK ENTER
Saving the adjustment setting
(For use with the �Power� remote control, slide the MOUSE/ADJUSTMENT switch to the ADJ. position.)
INPUT IrCOM
FREEZE
AUTO SYNC
(GUI) On-screen Display 2
1 Press MENU. 2 Press �/© to select �Fine Sync�. 3 Press �/� to select �Save Setting�, and then press ©. 4 Press �/� to select the desired memory location of the setting. 5 Press ENTER to save the setting. 6 To exit from the GUI, press MENU.
Selecting a saved setting
(For use with the �Power� remote control, slide the MOUSE/ADJUSTMENT switch to the ADJ. position.)
1 Press MENU. 2 Press �/© to select �Fine Sync�. 3 Press �/� to select �Select Setting�, and then press ©. 4 Press �/� to select the desired memory setting. 5 Press ENTER to select the setting. 6 To exit from the GUI, press MENU.
� If the memory position has not been set, the resolution and frequency will not be displayed. � When selecting the stored adjustment setting with �Select Setting�, the computer system should match the stored setting.
Operation
3
4
Mode Adjustment
Used to display image in the text and graphic modes. CONNECTING TO IBM-PC COMPUTERS � Ordinarily, the type of input signal is detected and the correct resolution mode (Text or Graphics) is automatically selected. However, for the following signals, set �Mode� on the �Fine Sync� menu screen to �ON� or �OFF� to select the projector�s resolution mode to match the computer display mode properly.
Mode Adjustment
(For use with the �Power� remote control, slide the MOUSE/ADJUSTMENT switch to the ADJ. position.) 1 Press MENU. 2 Press �/© to select �Fine Sync�. 3 Press �/� to select �Mode�. 4 Press �/© to select �ON� for graphic mode (640 dots 350 lines, 640 dots 400 lines or 1,152 dots 864 lines, 60 Hz) or �OFF� for text mode (720 dots 350 lines, 720 dots 400 lines or 1,024 dots 864 lines, 60 Hz). (For IBM-PC) Press �/© to select �ON� when connecting to a Macintosh II with 35 kHz dot frequency or �OFF� when connecting to a Macintosh LC Series computer with 34.79 kHz dot frequency. (For Macnitosh LC Series) 5 Press ENTER to save the setting. 6 To exit from the GUI, press MENU.
� When connecting third party video board and other Macintosh computers, set �Mode� on the �Fine Sync� menu screen to �ON� or �OFF� to select the correct display mode. � When the input signal is automatically detected or when there is no input signal, �Mode (---)� appears on the screen and the display mode cannot be changed. � Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)
27
|
|
|
> |
|
