|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Manual is actually a pack of schematics, good quality pictures.
 ;
Great service. Manual delivered at a great price. Reliable delivery service. They have a great selection. A recommended service!
 ;
I used your service and I found myself well I need service manual teac v plate 770 and I was able to access and remove the belt that erno routes. thanks I recommend it to all
 ;
At first I thought there had been a mix up as I required the service manual for the cassette unit and the one supplied was for the CD unit. However when I scrolled further down I realised that both had been scanned together! This enabled me to dismantle and repair the cassette unit as intended and I also have a copy of the manual for both the CD and graphic equaliser units should I ever need them. Thanks very much for a great service.
 ;
Excelent service, the manual is complete, very cheap and fast
Alberto
XG-V10XE
ADJUSTING THE PC INTERFACE (CPCi-0042CE12. PC I/F Unit)
1. Initializing the EEPROM
1) Press S2601 to call the process mode. 2) Execute the S1 command on the SSS menu. (The S1 command is used to get the PC boards initialized. Do not carry out the S2 command because otherwise all the other adjustment data than on the PC boards would be initialized.) 3) Make sure the program version VER.XXX on the SPECIAL menu is the latest one.
2. Adjusting the levels
2-1. Preparing the oscilloscope 1) Set the oscilloscope range to 1 Vdc/div. and 5 µs/div. 2-2. Connecting the PC interface 1) Connect the PC interface to the set and make sure the P8404, P8405 and P8502 connectors are all tight in position. 2) Connect a cable between the ANALOG OUTPUT terminal (signal generator) and the DSUB connector (projector's INPUT1). 3) Set the projector's INPUT SELECT to the INPUT1 position. 4) Set the signal generator to the XGA mode (1024 x 768, 60 Hz, 32 tones). Adjust the output amplitude between the black and white levels to 700 mVp-p (terminated with a 75-ohm impedance). 5) Turn on the power. 2-3. Adjusting and checking the levels 1) Press S2601 and call the process mode. 2) Adjust the SH-PHASE setting on the OUPUT3 menu to 8. (Make sure the onscreen display characters appear crisp and clear.) (Adjusting the A/D menu settings) 3) G-BRIGHT adjustment: Feed the black signal and adjust the G-BRIGHT setting on the A/D menu until there are bit dropouts. With the above adjustment completed, get the setting 4 points up. 4) R-BRIGHT adjustment: Feed the black signal and adjust the R-BRIGHT setting on the A/D menu until there are bit dropouts. With the above adjustment completed, get the setting 4 points up. 5) B-BRIGHT adjustment: Feed the black signal and adjust the B-BRIGHT setting on the A/D menu until there are bit dropouts. With the above adjustment completed, get the setting 3 points up. 6) G-D adjustment: Feed the white signal and adjust the G-D setting on the A/D menu until there are bit dropouts. 7) R-D adjustment: Feed the white signal and adjust the R-D setting on the A/D menu until there are bit dropouts. 8) B-D adjustment: Feed the white signal and adjust the B-D setting on the A/D menu until there are bit dropouts. 2-4. Adjusting the DTV settings 1) Feed the 480P Y signal to the INPUT1 terminal. Keep out the R (Pr) and B (Pb) signals. 2) G-BRIGHT adjustment: Adjust the G-BRIGHT setting to the same as that on the A/D menu. Then get the setting 2 points up. 3) CR-OFFSET adjustment: Adjust the CR-OFFSET setting to 16. 4) CB-OFFSET adjustment: Adjust the CB-OFFSET setting to 16. 5) Press S2601 to exit from the process mode.
35
|
|
 |
> |
|