|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
XL-3000/3000C
� Laser failure.
Is +6.2V applied to the emiter of Q861 ? No Yes Check the PWB pattern between emiter of Q607 and emiter of Q861.
Is +5V applied to the collector of Q861 ? No Yes
Check the peripheral parts of IC804 and Q861.
Is +5V applied to the pin 62 (VDD) of IC802 ? No Yes Is +5V applied to the pin 1 (VCC) of IC801 ? No Yes
Check the PWB pattern between collector of Q861 and pin 62 of IC802.
Check the PWB pattern between collector of Q861 and pin 1 of IC801.
Is 0V applied to the pin 57 (SEL) of IC802 ? No Yes
Does the laser come on when pattern cut between pin 8 (SEL) of IC801 and pin 57 (SEL) of IC802 ? Yes
No Check the PWB pattern between IC701 and IC802 (BUCK/CCE/ BUS0~3) Is approx. 2V applied to the collector of Q801. Yes Check CNP802/CNW3. If it is normal, the optical pickup is faulty. Check the peripheral parts of IC801 and Q801. If it is normal, the optical pickup is faulty.
No
� Focus failure.
Does the optical pickup move up and down when the disc is removed? Yes Is the following waveform ouput at the pin 43 (FEI) of IC802 when the disc is set? Yes
pin 43 (FEI)
No
Check as stated in item "FOCUS SERVO SAWTOOTH WAVE FAILURE".
Check the periphery of IC801 and CNP802/CNW3. Is it normal? No Yes The optical pickup is faulty.
pin 48 (FOO)
pin 44 (SBAD)
Is the waveform shown above input at the pin 44 (SBAD) of IC802? Yes IC801 is faulty.
No
Check the pattern between pin 13 of IC801 and pin 44 of IC802. Check the periphery of IC801 and CNP802/CNW3.
� 40 �
|
|
|
> |
|
