|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very good scan quality, only PC Board scan not enough contrast.
;
First of all I must say that I received the manual in just a few minutes after placing the order. The copy is well done and very readable. I will buy others soon... Thanks, Meyer
 ;
Good service manual. I gat all I want. Copy is good, but could be better. All clear and useful. I sincerely recommend.
;
The schematic is very helpful and the images are very good.The schematic is very helpful and the images are very good.The schematic is very helpful and the images are very good.The schematic is very helpful and the images are very good.The schematic is very helpful and the images are very good.The schematic is very helpful and the images are very good.
;
Welcome. The scheme is clearly helped me to repair. Worth to download it.
XM-405EQX
SERVICE MANUAL
US Model Canadian Model AEP Model UK Model E Model
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US, Canadian model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 40 watts/100 watts per channel minimum continuous average power into 4 ohms, 5 channels driven from 20 Hz to 20 kHz/200 Hz with no more than 0.04% total harmonic distortion per Car Audio Ad Hoc Committee standards. Other Specifications
Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Speaker impedance 2 � 8 � (stereo) 4 � 8 � (when used as a bridging amplifier) Maximum outputs 80 watts � 4 + 200 watts � 1 (at 4 �) Rated outputs (supply voltage at 14.4 V) 5 Speakers: 40 watts � 4 (20 Hz � 20 kHz, 0.04% THD, at 4 �) + 100 watts � 1 (20 � 200 Hz, 0.04% THD, at 4 �) 50 watts � 4 (20 Hz � 20 kHz, 0.1% THD, at 2 �) + 125 watts � 1 (20 � 200 Hz, 0.1% THD, at 2 �) 3 Speakers: 100 watts � 2 (20 Hz � 20 kHz, 0.1% THD, at 4 �) + 100 watts � 1 (20 � 200 Hz, 0.04% THD, at 4 �) Frequency response 5 Hz � 100 kHz ( +0 dB) �3 Harmonic distortion 0.005% or less (at 1 kHz, 4 �) Input level adjustment range 0.2 � 4.0 V (RCA pin jacks) 0.4 � 8.0 V (High level input) High-pass filter 50 � 200 Hz, �12 dB/oct Low-pass filter 50 � 200 Hz, �12 dB/oct Low boost 0 � 10 dB (40 Hz) Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 � 16 V Current drain at rated output: 33 A Remote input: 1.5 mA Dimensions Approx. 260 � 55 � 450 mm (w/h/d) (10 1/4 � 2 1/4 � 17 3/4 in.) not incl. projecting parts and controls Mass Approx. 4.7 kg (10 lb. 6 oz.) not incl. accessories Supplied accessories Mounting screws (4), Terminal cap (1) Design and specifications are subject to change without notice.
Notes on Chip Component Replacement � Never reuse a disconnected chip component. � Notice that the minus side of a tantalum capacitor may be damaged by heat.
STEREO POWER AMPLIFIER
MICROFILM
�1�
|
|
|
> |
|
