|
Who's Online
There currently are 6043 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
thank u so much for this manual that was so cheap that i thought it was a scam but i gambled anyway because it was too good of a deal to pass up and behold,the manual has everything and details of everything even the screws and im still amazed and very happy with my manual .so take my word and jump on it before they realize how cheap they selling thier manuals..thank you so much for taking time to read my thoughts
;
I do not have very much to say.
The price is quite covenient, delivery was better as promised (about 12 ours, against the specified 24 hours if I remember well), and the quality of the PDF is more than acceptable.
The Service Manual of Sansui R30 itself is also satisfactory: good graphic for schematics and layouts, simple and well structured.
Giovanni Bianchi
;
Happy to find finally a schematic for this amplifier. The schematic is of good quality, the pcb layout is useless: all is black. Never the less, it is very easy to find the components on the board using the schematics.
;
Hard to find manual was ready the next day. Scans were very legible (including schematics). All the essential parts of the service manual were present (adjustment procedure, schematics, and parts list). It would have been nice if the rest of the manual was included (disassembly procedure, theory of operation, etc.).
;
The Service Manual for the Kenwood KR-V55R provided by owner-manuals.com was as described/advertised. The contents provided the necessary information to effect a diagnosis of the unit. The schematics above all else was instrumental in tracing the the signal flow from component to component.
XR-A660SW, XR-A660EE
4.2 ADJUSTMENT FOR XR-A660EE
Note : Adjustment of XR-A660EE/MLWXJ/EE are the same as those of XR-A660/DLXJ/NC except for the following:
FM Tuner Section
Set the mode selector to FM BAND. Connect the wiring as shown in Fig. 1. FM SG (1kHz, ±75kHz dev.) Step No. Adjustment Title Frequency (MHz) Front End Sensitivity TUNED IND. Lighting Level Level (dBµV) Reception Frequency Display L6104 L6102 T6101 VR6201 Adjust so that the DC voltage between the IC6201-Pin 20 and GND becomes at maximum level. Adjust so that the indicator of TUNED IND. starts to light up. Adjustment Location
Specifications
1
70
0-30
70MHz
2
98
18±2
98MHz
Notes: Before adjusting, make sure there is no gap between L6101 and L6102 as well as between L6103 and L6104. If there is a gap between them, bring them into contact with each other first, and then make adjustments.
AM Tuner Section
Set the mode selector to AM BAND. Connect the wiring as shown in Fig. 1. AM SG (400Hz, 30% Mod.) Step No. Adjustment Title Frequency (kHz) Level (dBµV/m) Reception Frequency Display Adjustment Location Specifications
1
Front End Sensitivity
999*
1
35-45
999kHz*
1
T6201
Adjust so that the DC voltage between the IC6201-Pin 20 and GND becomes at maximum level.
*1: For the area using 10kHz step, frequencies should be 1000kHz
60cm Loop antenna
AM SG
Center
Center
AM antenna terminal
MPX SG
FM SG
PRODUCT
DC voltmeter
FM75� antenna terminal
Fig. 1 AM and FM Adjustment Wiring Diagram
FM/AM TUNER MODULE (AXQ7069)
AM antenna terminal T6201 AXX7041 YELLOW FM antenna terminal BLACK
L6101 T6101 L6102 L6103
VR6201
L6104
Fig. 2 Adjustment Points
12
|
|
|
> |
|