|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good quality. Quick service. I recommend to everyone.
;
Very good quality scan of the document. I am very pleased with what I got.
;
PDF Contains
Technical Data, Mechanical data, Detailed Circuit diagram with components value, PCB layout. Actual PCBs Print. Component List, Spare parts code list and Input output detail. It cover LBB1211, LBB1212, LBB1213, LBB1216, LBB1217.
It is the actual Service Manual for SQ10
;
very good manual with clear electrical schemes. Very helpful to find wat was wrong inside my microwave.
 ;
Hi, thankyou for providing the Nordmende Globetrotter original manufacturer's repair manual. Quality is very good and sharp - the PDF file was comfortably small to download. The only question is: why did it take so long to become ready for download?? Many thanks anyway, I fixed the fault in the radio thanks to the circuit.
regards: Nick
Pin No. 36 37 38 39 40 41 42 43 44
Pin Name LM LOD LM EJ N/R OUT P.ON CM ON TAPEON COLSEL RC IN1 TEST
I/O O O O O O O I I I
Function Loading/tape operation motor control signal output to the LB1638M (IC361) (For the loading direction and forward side operation) *1 Loading/tape operation motor control signal output to the LB1638M (IC361) (For the eject direction and reverse side operation) *1 Forward/reverse direction control signal output to the CXA2510Q (IC301) �L: forward direction, �H�: reverse direction Polar stereo detection signal output terminal �H�: polar stereo Not used (open) Capstan/reel motor (M901) drive signal output terminal �H�: motor on Tape system power supply on/off control signal output terminal �H�: tape on Setting terminal for the illumination color �L�: amber, �H�: green (fixed at �H�) Rotary remote commander shift key A/D input terminal Setting terminal for the test mode �L�: test mode (normally fixed at �H�) Power supply on/off control signal output terminal at the illumination and liquid crystal display driver (IC901) �H�: power on At power select switch (S501) on mode: �H� output at the accessory on At power select switch (S501) off mode: �H� output at the power on Beep sound output terminal Line muting control signal output terminal �H�: line muting on Chip enable signal output to the electrical volume (IC161) Chip enable signal output terminal Not used in this set (open) Serial data transfer clock signal output to the electrical volume (IC161) Serial data transfer clock signal output terminal Not used in this set (open) Serial data output to the electrical volume (IC161) Tape muting on/off control signal output to the CXA2510Q (IC301) �H�: tape muting on Dolby control in/out terminal At initial mode: valid/invalid selection input of dolby function (�L� input: valid) At normal mode: dolby on/off control signal output to the CXA2510Q (IC301) �H�: dolby on Dolby B/C selection control in/out terminal At initial mode: dolby B only/dolby B and C type selection input (�L� input: dolby B and C) At normal mode: dolby type selection signal output �L�: dolby B, �H�: dolby C Not used this function (fixed at �H�) Whether a music is present or not from CXA2510Q (IC301) is detected at auto music sensor �L�: music is present, �H�: music is not present METAL control in/out terminal At initial mode: auto/manual mode selection input of METAL function �L�: manual mode At manual mode: METAL on/off control signal output to the CXA2510Q (IC301) �H�: METAL on At auto mode: input at MTLIN (pin #º) Power supply on/off control signal output for the A/D converter �L�: power on Internal RAM reset detection signal input from the RN5VD23AA (IC651) Input terminal to check that RAM data are not destroyed due to low voltage This checking is made within 100 msec after reset System reset signal input from the reset signal generator (IC652) �L� is input for several 100 msec after power on, then it changes to �H� Sircs signal input from the remote control receiver (IC902) Battery detect signal input terminal �H�: battery on Power select switch (S501) input terminal �L�: off (halt mode), �H�: on (operation mode) Accessory detect signal input terminal �L�: accessory on Detects the removal of the attaching and removing type front panel block �L�: attaching
45
ILL ON
O
46 47 48 49 50 51 52 53
BEEP MUT VOLCE SUBCE VOLCKO SUBCKO VOLSO TAPMUT
O O O O O O O O
54
DOLON
I/O
55
DOLBC
I/O
56
AMSIN
I
57
MTLSEL
I/O
58 59
AD ON RAMBU
O I
60 61 62 63 64 65
RESET SIRCS BU IN PW SEL ACCIN NOSESW
I I I I I I
� 31 �
|
|
|
> |
|
