|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I found this service manual to be complete in every detail except for troubleshooting charts. It would be helpful if it had a set of troubleshooting charts; however it is a very good manual otherwise and for the price it is very well worth it.
 ;
Complete manual included schematics layouts and alignment procedure, clear to read and magnify, extremely pleased with manual and owner manual . com's service
;
perfect, i am very satisfait for the réception of the sansui r-5l service manual, thank you very much
;
Thank you, this is a rare document. Few others have it, but they charge way more for a download.
Great deal (even if you have to wait a few hours to get it).
;
The purchased manual is an high quality scan of the original Philips paper-based Service Manual. I am very satisfied!
ADJUSTMENT
<TUNER>
(MX-NMT1 C.B
000)
u
TUNER
(
)( �
)(
(
OEcl
7 H)
�FE801
(:
I
1-i 71
�
L772
1
�5
q
,
L981
TP1
(v
�)
(AUT
@
TP6
(LCH)
1
�7��;1> H
T~4
I
TP6(Lch), location : TP7(Rch)
L
EWLNCE)
(Dc
u
1/3
@
(DC BALANCE)
+
I
@m@
< TUNER 1. Clock Settings Method: SECTION> frequency : Check point: TP2 andcheck thatthetest
)
o
7
@c
6.
AM(MW) Settings
IF Adjustment :�q Test
q
qTest
Set
point:
to AM1710kHz + 45 Hz.
pointis
Adjustment
2160kHz
L772
.. .. ... ... ... ... .... .. ... ... ... ... ... ... ... ... ..45OMz
2.
MW
VT Check : c Test that more point: TP1 1710kHz and MW 530kHz and check and is less than 8.5 V(1710kHz)
7.
DC Balance/ Settings :
q
Mono Test point:
Distortion TP3,
Adjustment TP4 (DC L771 Balance) (Distortion)
Settings Method
: Set to MW
TP6(Lch),
q q
TP7(Rch)
the test point than
Adjustment Input level
location: : 54dB and
0.6V(530kHz). Method:
Set to FM voltage
98.OMHZ TP3
adjust
L771 becomes is less
so that
the
3.
MW
Tracking :
q
Adjustment Test point: TP6(Lch), location : 8. so that the Auto Stop TP7(Rch)
between check that
and TP4
OV k 0.04V. than 1.3%
Settings
Next,
the distortion
q
Adjustment
L981(1/3) Method : Set to MW test point
. ... ... ... ... ... .. .. .. .... .. .... ... ... 1000kHz 1000kHz is max. and adjust L98 1(1/3)
Level
Check
AM(MW) Settings :
q
Test Input
point: level
TP5 : 52dB 1000kHz and check that the auto stop is at
q
4.
FM VT Check Settings Method: :
q
Method: point: TP1 108.OMHZ
8.OV.
Set to AM 3762dB.
Test
Set to FM less than Set to FM more than
and check and check
that that
the test point the test point
is FM is Settings :
q q
87.5MHz 0.5V.
Test Input
point: level
TP5 : 25dB and check that the auto stop is at
Method: 5. FM Tracking Settings Method : :
q q
Set to FM 25dB
98.OMHZ
Check Test less point: than TP6(Lch), 98.OMHZ 9.OdB. TP7(Rch) and check that the test point is
+ 10dB.
Set to PM
46
|
|
|
> |
|
