|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
excellent value & price! Includes everything you need to know about the NN-C777! I would buy this again.
;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
;
I purchased the unit from a private party and the original owners manual was not available. Having the ability to download it was extremely helpful and clarified operating the equipment immensely. This is a complicated unit and without the manual I would not have been able to maximize it's potential. Thank you.
;
Being a user of older radios of many kinds, preferring them over more modern rigs, this manual was invaluable in the programming of my two. I now know for certain what the assorted buttons functions are, and am very grateful to have found this excellent site. Many thanks for your assistance, Tony.
NOTES: � If you have selected �NO� for the surround back speaker (see page 24), you cannot select this setting. 6.1-channel and 5.1-channel software is played back in the same way as �OFF� is selected for above setting. � When the sound is not output from the surround back speaker even though playing back Dolby Digital EX software (bearing the mark ) setting �EX/ES� to �AUTO,� select �ON� instead of �AUTO.�
Select one of the following settings: 80Hz 100Hz 120Hz 150Hz :Select when the cone speaker unit built in the speaker is about 12 cm. :Select when the cone speaker unit built in the speaker is about 10 cm. :Select when the cone speaker unit built in the speaker is about 8 cm. :Select when the cone speaker unit built in the speaker is about 6 cm. :Select when the cone speaker unit built in the speaker is less than 5 cm.
Setting the speaker distance
�FRNT D (front speaker distance), CNTR D (center speaker distance), SURR D (surround speaker distance), BACK D (surround back speaker distance)
The distance from your listening point to the speakers is another important element to obtain the best possible sound from the Surround and DSP modes. You need to set the distance from your listening point to the speakers. By referring to the speaker distance setting, this system automatically sets the delay time of the sound through each speaker so that sounds through all the speakers can reach you at the same time. Set the distance from the listening point to each speaker with the range of 0.3 m to 9.0 m (in 0.3 m intervals).
NOTE: If you have selected �NO� for �BACK SP� (see page 24), you cannot set the speaker distance for the surround back speaker.
200Hz
CAUTION: When using the supplied speakers, select �200Hz.�
NOTE: Crossover frequency is not valid for the HEADPHONE mode.
Setting the phase of subwoofer
�PHASE
Subwoofer phase is closely related with the distance from the listening position to the front speakers and subwoofer. You can change the phase to obtain better bass sound. Select one of the following settings: NORMAL :Normally select this. :Select when you feel the bass sound is better with this mode rather than with �NORMAL.�
C L R
Subwoofer 3.3 m 3.0 m 2.7 m 2.4 m 2.1 m
REVERS
LS
RS
Setting the video output for DVD playback�M.OUT (monitor out)
After connecting your TV (see page 7), select the video output jack type you watch the DVD playback. Setting this properly, you can use AV COMPU LINK remote control system.�The TV automatically changes the video input mode to the appropriate position (see �AV COMPU LINK remote control system� on pages 60 and 61). � �VIDEO� is initial setting. Select one of the following settings: VIDEO S :Select when you watch the DVD playback through the VIDEO jack. :Select when you watch the DVD playback through the S-VIDEO jack.
SB
Ex.: In the above case, set the speaker distance as follows: FRNT D : 3.0 m CNTR D : 3.0 m SURR D : 2.7 m BACK D : 2.4 m
Setting the crossover frequency�CROSS
Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this system automatically reallocates the bass sound elements assigned to the small speaker to the large speakers. To use this function properly, set the crossover frequency level according to the size of the small speaker connected. � If you have selected �LARGE� for all speakers, this function does not take effect and you cannot change the frequency.
COMPNT:Select when you watch the DVD playback through the COMPONENT VIDEO OUT jacks.
25
English
|
|
|
> |
|
