|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very glad recieving the service manal from You. Manuals were delivered promptly and were correct as advertised. A complete and very usefull service manual with all details. Thank you!
;
Very clear copy. No pages missing. Big bonus is that it includes supplement. Price is affordable compared to what others ask for.
;
Found the quality of the copy excellent and a very quick service. I would certainly recommend the service.
;
Good quality, clear diagrams. Exactly what I needed.
 ;
Good product. All the information is invcluded, but due to the complexity of the amplifier, it still is difficult to get it to operation again.
Symbol/PartsCod) -------------------------------------------------------
sPower supply
Batteries used
Type Lithium battery Lithium battery Model CR2032 CR2032 Quantity 2 1 Use Unit operation Memory backup
sSynchronization
Supplied Items
· · · · · · · · · ·
Sharp Electronic Organizer One 3.5" Floppy Disk (PC Interface Software) PC Interface Cable PC Iuterface Software User�s Guide Windows 2000 Professional, Windows 98, or Windows 95 8MB free hard disk space VGA monitor or better Microsoft Mouse or compatible Pointing Device 3.5" disk drive
· Do not remove both the operating and memory backup batteries
at the same time. Doing so will clear the memory of its contents.
System Requirements
· Be sure to write down any important information stored in the
memory before replacing the batteries.
1. Precautions
Since improper use of the batteries may cause leakage or explosion, strictly observe the following instructions.
One available serial port with D-sub 9-pin connector And for Windows 2000 Professional :
· · · ·
Insert the battery with its positive side (+) correctly positioned. Never throw batteries into a fire because they might explode. Keep batteries out of the reach of children.
· 133MHz or higher Pentium-compatible CPU · 64MB RAM available
And for Windows 98 , Windows 95 :
When batteries become low, remove them from the Organizer immediately to avoid battery leakage and corrosion inside the Organizer. Because the batteries in the Organizer were installed at the factory, they may become depleted before the specified expiration time is reached.
· IBM-compatible 486 or Pentium-compatible CPU(66MHz or higher) · 24MB RAM available
Connecting Your Organizer to a PC
1. Turn off your PC and the Organizer. 2. Connect the standard 9-pin connector of the PC interface cable into a COM port on your PC.
2. Operating Batteries Replacement
(1) Battery replacement time
When " BATT " is displayed, immediately replace the batteries with new ones. If the battery level is very low, the alarms or the key touch tone may not sound, or similarly the Backlight may remain on for less than the set interval or it may not function. Continued use of the Organizer with low batteries can alter or clear the memory contents. Memory contents may be lost if the batteries are improperly replaced or if the following instructions are disregarded.
· Using a 25-pin connector instead of the standard 9-pin connector
requires an additional adaptor. 3. Connect the other end of the PC Interface Cable into the PC interface connector located on the left side of the Organizer.
(2) Replacing the batteries
· Make sure the power is turned off before replacing the batteries. · Do not press ON until the battery replacement procedure is
completed. 1. Press OFF to turn the power off. 2. Loosen the screw (counterclockwise) and remove the battery holder cover on the back of the unit.
PC Interface Cable (supplied)
3. Remove the used batteries using a ball-point pen or similar object. · Do not use a mechanical pencil or sharp pointed object. 4. Install 2 new batteries with the positive sides (+) facing up. 5. Replace the holder cover and secure it with the screw. 6. The power will be turned on 2 to 3 seconds after ON is pressed. If the power does not come on, press the RESET switch. 7. Set the clock to the correct time.
|
|
|
> |
|
