|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly as described, a Service Manual complete with the schematics and PCB layout delivered in a timely manner. Many thanks for the great service.
 ;
some of the writing is a bit blur but the part in the schmatic was great and i have fixed the machine thanks
;
Well.. I'd searched for this manual and although I found many copies online I was pleased to find your website with a well balanced pricing system and easy to search and follow links. That together with the very quick response time was just what I was looking for.. being a very impatient tech.. ;-) I had the service manual in front of me within a short time.
Bookmarked.. and you can bet I will always come here first for my service & user manuals..
best regards
Ed(Tony) Foley
G7WHK
;
I will definitely be back for more information when I need it.
;
The service manual when downloaded and printed out was clear and easy to read. I would have liked to have been able to enlarge some details, but this was not possible as the file permissions did not allow this. The service was very good. The time taken from placing my order to downloading the document was only a few minutes.
1-4 YP-D9000(UC,CE)
Miscellaneous
About the Ink Ribbon and Paper
Two types of ribbon and two types of paper are used: one type of each for the Dye Sublimation Printing System and the Variable Dot Printing System. When the ribbon and paper are changed, the printer automatically selects the corresponding system. Of course the type of ribbon and the type of paper must both correspond to the same printing system. The relationship between the printing systems and types of ribbon and paper are as follows:
Ribbon Dye Sublimation System A3++ UPR-9510 A4++ UPR-9511 Variable Dot System A3++ UPR-9550 A4++ UPR-9551 Paper A3++ UPP-9510 A4++ UPP-9511 A3++ UPP-9550 A4++ UPP-9551
Adding Memory
The memory in this product can be expanded using 72-pin SIMMs (Single Inline Memory Modules). The control unit has six memory slots which accept any combination of 8, 16, and 32 MB SIMMs. The maximum capacity for memory expansion is 192 MB. If memory has been added, it will be recognized automatically at power-up. Refer to �Confirming Internal Printer Configuration� (page 32) to confirm that the added memory has been recognized.
1 2
Power off the printer. Remove the screws indicated by the arrows below on the rear of the printer. Do not remove screws not indicated by arrows.
Changing Printing Systems When changing from dye sublimation printing to variable dot printing (or vice versa), you must change to the appropriate ribbon and paper for that system. Refer to the manuals supplied with the ribbon and paper for the changing procedures.
Note
If the type of ribbon and the type of paper do not match, printing is not possible. Notes about the ribbon � Ink ribbon should not be re-used. � Do not store ink ribbon in high temperature or humidity. � When storing an ink ribbon for a long time between uses, store it in the moistureproof bag in which it came. � Do not store ink ribbon in a dusty place. If it picks up dust, the printed images may be soiled, and the print head may be damaged. Notes about paper � Use only paper that is specifically intended for the printer. Other types of paper may cause problems such as paper jams. � The paper loaded into the printer should remain in the package. � Do not add paper to the paper package. � Match the type of paper to the printing system being used. � Do not store paper in high temperature or humidity. � When storing paper for a long time between uses, store it in the moisture-proof bag in which it came. � Do not store paper in a dusty place. If it picks up dust, the printed images may be soiled, and the thermal head may be damaged.
3
Slowly pull the Control Unit out about 10 cm (4 inch).
Note
Pulling the Control Unit too hard or too far could cause damage.
Miscellaneous
29
30
Miscellaneous
|
|
|
> |
|
