Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
Text excerpt from page 5 (click to view)
Replacement of the filter(s)
Should be done with every 5th replacement of the dust bag, s-bag® Never use the vacuum cleaner without filter(s). A Model without exhaust filter has to be equipped with a combination-filter (micro-filter + motor-filter, Ref. No. EF 74). 24 Open the front cover and lift out the insert holding the s-bag®. 28 Pull the filter(s) holder upwards until coming away from the groove. Carefully pull the old, dirty filter(s) out of the filter holder and replace with a new filter(s). 29 Reattach the filter holder containing the new filter(s). 27 Replace the insert holding the s-bag® and then close the cover. B Model with exhaust filter Follow steps 24, 28 and replace old motor-filter with a new one. Then follow steps 29, 27. Replacement of the exhaust filter* There are three types*** of exhaust filter: � Microfilter (Ref. No. EF 17) � Hepa H12*** non washable (Ref. No. EF H12) � Hepa H12 washable (Ref. No. EF H12W) The filters must always be replaced with new ones and cannot be washed (if not mentioned ). 30 Place your thumbs on the back edge of the lid and then open the lid by pulling the handle backwards and upwards with your index/middle finger. 31 Lift out the filter. Insert a new filter and replace the lid as shown.
Cleaning the floor nozzle 39 To avoid deterioration of suction power, frequently clean the carpet/ hard floor nozzle. The easiest way to clean it is by using the hose handle. 36* Press each wheel-hub and draw away the wheels. Use the crevice nozzle to clean the wheel axles. Remove dust-balls, hair or other objects that may be entangled. Replace the wheel by pressing them onto the axles. 37* Larger objects can be accessed by removing the connection hose from the nozzle (press the small catches located on each side and simultaneously draw the connection tube outwards in an upright position). 38* Remove the object(s) and replace the connection hose. Cleaning the turbo nozzle* 40 Disconnect the nozzle from the vacuum cleaner tube and remove entangled threads, etc. by snipping them away with scissors. Use the hose handle to clean the nozzle.
Troubleshooting
The vacuum cleaner does not start � Check that the cable is connected to the mains. � Check that the plug and cable are not damaged. � Check for a blown fuse. The vacuum cleaner stops � Check whether the dust bag, s-bag® is full. If so, replace it with a new one. � � Is the nozzle, tube or hose blocked? Are the filters blocked?
Cleaning the hose and nozzle
The vacuum cleaner stops automatically if the nozzle, tube, hose or filters and s-bag® becomes blocked. In such cases, disconnect from mains and allow to cool for 20-30 minutes. Clear blockage and/or replace filters and s-bag® and restart. Tubes and hoses 34 Use a cleaning strip or similar to clear the tubes and hose. 3* Hose handle could be dismantled from hose if cleaning is needed. 35 It may also be possible to remove the obstruction in the hose by squeezing it. However, be careful in case the obstruction is caused by glass or needles caught inside the hose. Note: The warranty does not cover any damage to the hose caused by cleaning it.
Water has entered the vacuum cleaner It will be necessary to replace the motor at an authorised Electrolux service centre. Damage to the motor caused by the penetration of water is not covered by the warranty.
