|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
 ;
Received downlink in less then 8 hours, Item was in good copy condition, and told me how to program the clock timer. The price was very resonable, and the process was very automated and was GREAT to work with.
;
Fast service, document is OK. Thanks! Searched for it long time.
;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
HOOKING UP YOUR TV (ANTENNA/CABLE CONNECTIONS) (CONT�D)
VCR
TO
TV
Connect your Antenna or Cable signal to the ANTENNA IN jack on the VCR. Connect a coaxial cable to the RF OUT or ANTENNA OUT jack on the VCR and to the ANT(enna) IN jack on the TV. The coaxial cable may be supplied with the VCR. Refer to the VCR owner's manual for other possible connections and for operating details.
BASIC CONNECTION
T
he basic Antenna/Cable to VCR to TV connection is
shown here. If you have a Cable Box, refer to the VCR owner�s manual for details.
300 to 75� Adaptor
Outdoor VHF/UHF Antenna Coaxial cable
ANTENNA IN RF/ANTENNA OUT
PAUSE
RECORD
Cable TV signal
POWER VCR/TV CHANNEL
REW
PLAY
F.FWD
VIDEO
L AUDIO R
STOP/EJECT MENU STATUS/EXIT
ANT.IN
VCR (example only)
Back of TV SMART HELP
If you do not have a Cable Box, then you're ready to connect your Cable TV signal to the TV. Go to step 2. If you have a Cable Box: Connect the Cable TV signal to the IN jack on the Cable Box. If you do not have a Cable Box, connect the Cable TV signal directly to the ANT(enna) IN jack on the TV. If you have a Cable Box: Use a coaxial cable to connect the OUT jack of the Cable Box to the ANT(enna) IN jack on the TV. NOTE: The coaxial cable might be supplied by the Cable TV company. To select only the channels on your Cable system, see Auto Install (page 4). If you use a Cable Box, set the TV to the same channel as the CH 3/4 switch on the back of the Cable Box and select channels at the Cable Box.
CABLE TV
CABLE/CABLE BOX
Y
our Cable TV signal may be a single (75�) cable or a Cable Box installation. In either case, the connection to the TV is very easy.
Cable TV Company Cable TV Signal (75�)
Cable Box
IN OUT
OR
Coaxial cable
Note to the Cable TV System Installer: This reminder is provided to call the Cable TV system installer�s attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.
ANT.IN
Back of TV
USING
THE
FRONT AUDIO/VIDEO IN JACKS
SMART HELP
When you are finished watching the tape, press the TV/AUX button on the TV remote control to return to viewing normal TV channels. If the VCR or camcorder has Right and Left AUDIO OUT jacks, you will need a �Y� connector cable in order to connect the camcorder/VCR to the TV. Or, check the owner�s manual of the camcorder or VCR. It may explain how to connect to a TV that has a single AUDIO In jack.
AUDIO/VIDEO IN JACKS
or more convenient tape playback from a camcorder or VCR, use the AUDIO and
F
VIDEO In jacks on the front of the TV. These easily accessible jacks allow quick connections between the TV and the VCR or camcorder.
Connect a video cable (not supplied) to the VIDEO OUT jack of the camcorder/VCR and to the VIDEO In jack on the front of the TV.
Connect an audio cable (not supplied) to the AUDIO OUT jack of the camcorder/VCR and to the AUDIO In jack on the front of the TV.
When you play a tape, select A/V IN at the TV. Press the TV/AUX button to select A/V IN. A/V IN will appear on the screen.
Turn on the camcorder/VCR and press the PLAY button on the camcorder/VCR. When you are finished watching the tape, press the STOP button on the camcorder/VCR.
VIDEO AUDIO EARPHONE MENU VOLUME CHANNEL POWER
1
AUDIO VIDEO OUT
Video Cable (yellow) from VIDEO OUT to VIDEO In
Audio Cable (white) from AUDIO OUT to Audio In
2
-3-
|
|
|
> |
|
