|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
;
I PURHASED THIS PRODUCT BECAUSE I WAS HAVING PROBLEMS WITH MY CDR20 HARMAN KARDON RECORDER. WHICH I PURCHASED NEW 12 YEARS AGO. AFTER REVIEWING THE MANUAL, I WAS ABLE TO ADJUST THE TENSIONER IN THE SYSTEM. WORKS LIKE A CHAMP!.
SAVED ME AT LEAST 100.00 WHICH WAS WHAT A SERVICE REPAIR STATION WANTED. GREAT MANUAL EASY TO READ. SPECIALLY AFTER I PRINTED THE PAGES WHICH DEALT WITH MY RECORDER. THANKS A LOT!!!!!!!!
;
You can fully trust on this one!
All the schematics are very crear an in one piece per page
;
I have never bought a service manual which is as competely readable as this althogh it was a scanned pdf. Thank you for this succesful manual also cheaper than other sites.
25WG3
CHECKING OPERATION (VIDEO & AUDIO) NO CHECKING POINT SETTING CONDITION WAVEFORM OR OTHERS
12 NORMAL 1. Receive the MUSIC SOUND SIGNAL. If nothing is display mean 2. Press NORMAL key to set the sound contrast, colour, bright, tint, sound control settings will be preset to 2. Press NORMAL key to set the picture sharpness are all in normal normal setting as listed below: condition to normal . When the setting. BASS: CENTER MIDDLE: CENTER
NO CHECKING POINT SETTING CONDITION WAVEFORM OR OTHERS
6 NORMAL 1. Receive "COLOUR BAR PATTERN" If nothing is display mean condition to normal . When the sharpness are all in normal
signal. contrast, colour, bright, tint, NORMAL key is pressed, all the initial setting.
NORMAL key is pressed, all the initial picture control settings will be preset to TREBLE: CENTER normal setting as listed below: BALANCE: CENTER Contrast: MAX. Colour: CENTER 2. Press the CH UP / DOWN key for Brightness: CENTER SURROUND control setting with the R/C. Tint: CENTER 3. Press Volume Up to switch Surround Sharpness: CENTER Mode as follows, MOVIE/DISCO/POP/ 13 SURROUND 1. Receive the MUSIC SOUND SIGNAL. ROCK/CLASSIC/SPORTS/SIMULATED/ 7 CH COLOUR All Ch (1~99) will have an OSD display of OFF. 4. Make sure each mode is working properly. 14 SYSTEM 1. Receive the "PAL COLOUR BAR
DISPLAY the channel number in green colour under
AFT ON condition.
8 BASS 1. Receive the MUSIC SOUND SIGNAL. PATTERN" signal. Press the SYSTEM
2. Press CH UP / DOWN for key to set the COLOUR SYSTEM is OK or not. 3. Increase or decrease the BASS by signal. Press SYSTEM key to set the COLOUR SYSTEM mode to AUTO mode. Colour Bar signal is OK or not. 3. Receive the "NTSC 3.58 COLOUR BAR"
SOUND control setting with the R/C, MODE to AUTO mode. Check whether select BASS. colour of the PAL Colour Bar signal 2. Receive the "NTSC 4.43 COLOUR BAR" using the VOLUME UP / DOWN key.
4. Check whether the BASS (low
frequency) is OK or not. Check whether colour of the N4.43
12
2. Press Volume Up to switch each mode, 16 NOISE MUTE 1. Receive "PAL COLOUR BAR" signal. TREBLE. CHECKING 2. Turn up the volume control to maximum, 3. Increase or decrease the TREBLE by 4. Finally turn down the volume of CTV to 17 BILINGUAL 1. Receive "DUAL SOUND" signal. are okay separately or not. right speakers is OK or not.
9 MIDDLE 1. Receive the MUSIC SOUND SIGNAL.
2. Press the CH UP / DOWN key for SOUND signal. Press SYSTEM key to set the
control setting with R/C, select the COLOUR SYSTEM mode to AUTO MIDDLE. mode. Check whether colour of the N3.58 Colour Bar signal is OK not. 3. Increase or decrease the MIDDLE by
4. Check whether the MIDDLE (MIDDLE mode as follows, SAVE/ AV SELECT/ NR/
using the VOLUME UP / DOWN key. 15 1. Press FUNCTION key to select each
frequency) is OK or not. BLUE BACK/OSD.
10 TREBLE 1. Receive the MUSIC SOUND SIGNAL. make sure each mode is working
2. Press the CH UP / DOWN key for SOUND properly.
control setting with R/C, select the
4. Check whether the TREBLE (HIGH state.
using the VOLUME UP / DOWN key. speakers. Then put the unit in no signal
make sure sound is heard from the
frequency) OK or not. 3. Be sure that the sound mute is effective.
11 BALANCE 1. Receive the MUSIC SOUND SIGNAL. minimum.
2. Press the CH UP / DOWN key for SOUND
3. Increase decrease the left or right BILINGUAL.
control setting with R/C, select the 2. Press CH UP/DOWN key for SOUND BALANCE. control setting with the R/C, select
speaker BALANCE by using the 3. Press VOLUME UP/DOWN to select VOLUME UP / DOWN key. 1 & SOUND 2.
4. Check whether the BALANCE of left and 4. Check whether 1 & SOUND 2
|
|
|
> |
|
