|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
;
Complete manual including mechanical part in good pdf quality. Shaded greys of the pcb due to pdf not perfect but usable.
D
FM Abgleich
GB
FM Alignment
Bitte achten Sie darauf, da� die Stationstasten vor dem Abgleich mit bestimmten Frequenzen belegt werden müssen (siehe Seite 5).
Please observe that the station preset push-buttons have to be programmed to specified frequencies before the parameter programming (see page 5).
FM Phasenschieber - Abgleich
Künstliche Antenne (8 627 105 356) verwenden. Betriebsart ................................ FM Stationstaste ............................ 1 (97,2 MHz) Me�punkt ................................. MP 153 (X12/7) Abgleichelement ...................... Z 152 Spezifikation ............................. H>L Sprung Me�instrument ......................... Oszilloskop Signalquelle ............................. Me�sender f = 97,2 MHz, fmod = 1 kHz Hub = 22,5 kHz Signaleingang .......................... E' = 40 dBµV (+Bedämpfung!) 1. Klemmen Sie das Oszilloskop an MP 153 und Masse an. Schalten Sie den Oszilloskopeingang auf DC. 2. Stellen Sie den Me�sender auf 97,2 MHz, mit 22,5 kHz Hub und 1 kHz Modulation ein. 3. Speisen Sie das HF-Signal E' = 40 dBµV in die Antennenbuchse ein (Dämpfung der künstlichen Antenne beachten). 4. Drücken Sie die Stationstaste 1 (97,2 MHz). 5. Verstimmen Sie den Me�sender mit 1 kHz-Schritten um die halbe SL-Stop-Fensterbreite, d.h. auf 97,170 oder 97,230 MHz (siehe Skizze). Zwischen 29 kHz und 31 kHz von der Fenstermitte (97,200 MHz) sollte der oszillierende H>L Sprung an MP 153 erfolgen. Erfolgt der H>L Sprung nicht, geben Sie die halbe SL-StopFensterbreite von 30 kHz am Me�sender vor (97,170 oder 97,230 MHz), und stellen Sie den H>L Sprung mit Z 152 an MP 153 ein. 6. �berprüfen Sie abschlie�end die Fenstersymmetrie und korrigieren Sie die Einstellung von Z 152 ggf. erneut.
FM phase-shifter alignment
Use the dummy antenna (8 627 105 356). Operating mode ....................... FM Preset button ............................ 1 (97.2 MHz) Measuring point ....................... MP 153 (X12/7) Alignment element ................... Z 152 Specification ............................. H>L change Measuring instrument .............. oscilloscope Signal source ........................... signal generator f = 97.2 MHz, fmod = 1 kHz deviation = 22.5 kHz Signal input .............................. E' = 40 dBµV (+attenuation!) 1. Connect the oscilloscope to MP 153 and ground. Set the oscilloscope input to dc. 2. Adjust the signal generator to 97.2 MHz, 22.5 kHz deviation with the modulation of 1 kHz. 3. Feed the RF signal E' = 40 dBµV into the antenna input (observe the attenuation of the dummy antenna). 4. Press preset push-button 1 (97.2 MHz). 5. Detune the signal generator with steps of 1 kHz by half the width of the search tuning stop window, i.e. to 97.230 or 97.170 MHz (see sketch). The oscillating H>L level change at MP 153 should appear at about 29 to 31 kHz off the channel centre (97.200 MHz). If this is found to be different, tune to an offset of 30 kHz (97.170 or 97.230 MHz) and use Z 152 to adjust the H>L change at MP 153. 6. Finally check both slopes with regard of the window centre and make a correction if necessary.
Beispiel:
funterer H>L Sprung + foberer H>L Sprung 2 = fFenstermitte
Example:
funterer H>L level + foberer H>L level = fwindow centre 2
97,170
+ 2
97,230 = 97,200
97,170
+ 2
97,230 = 97,200
Die Abweichung von der Fenstermitte (97,200 MHz) darf bis zu ± 2 kHz betragen.
The permissible unbalance of the centre is 97.200 MHz ± 2 kHz.
97,170 MHz
97,200 MHz
97,230 MHz
5 Volt
0 Volt
60 kHz
97,169 MHz
� Im Anschlu� an diesen Abgleich müssen die DX/LO Programmierungen für FM und die RDS Grundempfindlichkeit neu programmiert werden (siehe Seite 11 + 12). - 16 �
97,231 MHz
At the end of this alignment DX/LO programming for FM and RDS - basic sensitivity must be redone. (see page 11 + 12).
|
|
|
> |
|
