|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the original Service Manual from Nordmende, Germany. Contains the circuit diagram, PCB layout, adjust/tune instructions as well. It is NOT in English but in GERMAN language! That was quite right for my german friend from the lower east side in Berlin.
 ;
Received via e-mail this PDF manual is worth the money. This is a quality scan of a manual in excellent condition and is just as good as having the original manual in hand. I have later seen the original manual and it was printed in colour, but this particular manual is black & white but scan resolution is high end quality! All drawings and pictures are presented in great detail. So, nearly perfect score in my opinion.
If you own the turntable you also should own the manual!
;
I was very satisfied with the service manual I ordered and downloaded. I will definitely buy again from this seller.
;
Great product. Recieved it fast...exactly as advertised.
;
Manuals were delivered promptly and were correct as advertised. No issues with the download link which was provided promptly after everything was processed. Very pleasant experience
SETTING CLOCK RESETTING THE MICROCOMPUTER
In this example, clock is set for 12-hour (AM 12:00) sysReset microcomputer under the following conditions:
1 Press ON/STAND-BY button to enter stand-by mode. q If the display is not correct. MEMORY/SET
q If the operation is not correct. POWER
X-BASS/ (Main unit operation) tem. q To erase all of the stored memory contents (clock and timer DEMO settings, tuner and CD presets).
ON/ ON/ Press ON/STAND-BY button to enter the stand-by mode. STAND-BY STAND-BY
Press the CLOCK button. POWER Within 5 seconds, press the MEMORY/SET button.
1 3 2 While pressing down button and the X-BASS/DEMO
display mode. second. "AM 12:00" � The 12-hour display q "CLEAR AL" will appear. "AM 0:00" � The 12-hour display will appear. TIME "0:00" � The 24-hour display will appear. (0:00 23:59) q Note that this can only be set when the unit is first installed or it has been reset.
presets.
2
CLOCK 4 Press TUNING/TIME ( or ) to select time button, hold down the ON/STAND-BY button for at least 1
TUNING/ (AM 12:00 PM 11:59) Caution:
q The operation explained above will erase all data stored in (AM 0:00 PM 11:59) memory including clock timer settings, tuner and CD ( )
5 Press the MEMORY/SET button. 2 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. q When the 12-hour display is selected, "AM" will change automatically to "PM".
3
7 Press the MEMORY/SET button.
minutes. q Press the TUNING/TIME ( or ) button once to advance minute intervals. q The hour setting will not even if minutes advance from "59" to "00". q The clock starts operating from "0" second. (Seconds are not displayed.) And then the clock display will disappear after a few seconds.
4 8 Press TUNING/TIME ( o r ) button to adjust the
OPERATION MANUAL
�5�
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds. Note: q The clock display will flash on and off at push of the CLOCK button when the AC supply is restored after a power failure occurs or after the AC power cord is disconnected. time.
12:00 AM 0:00 by 1 minute. Hold it down to change the time in 5
5 9 Press the MEMORY/SET button.
6
7
8 If this happens, follow procedure below to change the clock
To change the clock time:
9 xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button. zPerform steps 6 9 above.
To change the time display mode:
xPerform steps 1 2 in the section "RESETTING THE
MICROCOMPUTER", on page 15.
CD-BA150
yPerform steps 1 9 above.
|
|
|
> |
|
