|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great Manual. This manual is available no where else. It was exactly what I was looking for. Only in German.
 ;
This GRUNDIG UV5A Owner Manual is not only an instruction manual but a total functional circuit description of the Multimeter and includes circuit diagram at the end pages. It is very helpful for repairing and calibrating the instrument. It is written in two languages English and German for international support. It was very easy to repair my unit with this document. Regards, Regis Pauly, Electrical Engineer.
;
The owner's manual was evetything I thought it would be. I was able to print it out using both sides of the paper in quick order, saving me a search online for a used one.
;
Хорошее качество сканирования.
Мануал пришел часов эдак через 12. В целом доволен.
;
Fantastic quality and impressive delivery time. Based on this manual, I recommend this service without hesitation! Five Stars for certain.
5 � Recording
Basic recording
1. Load a recordable disc into the unit. As the disc loaded, the display shows TOC Reading, with the period flashing. 2. Press the INPUT SELECT key to select a recording source (see �Input selection� on page 25). If a digital source is selected, and the connection or the signal are improper, the error message
D-IN UNLOCK! will appear on the display.
4. Press the PLAY key to start recording. Pressing the READY key stands by recording temporarily. To restart recording, press the READY key or PLAY key again. When recording stops, the display shows PMA Writing (Program Memory Area) flashing for a few seconds as the unit writes to the disc.
NOTE
5. Press the STOP key to stop recording.
3. Press the RECORD key. The unit enters record ready mode, as shown by the REC and READY indicators on the display.
NOTE
When PMA Writing is shown on the display, all keys are ignored. To confirm the total recording time, use the REC TIME option in the SYSTEM sub-menu (see �Operation basics� on page 1).
NOTE
As the unit enters record ready mode, the display shows Now OPC (Optimum Power Control) occasionally, as the unit prepares to record on the disc.
To adjust the level of the source, following the guidelines in �Input selection� on page 25.
NOTE
The red �OVER� indicators on the meters should never light. Unlike analog equipment, digital audio units pro-duce extremely unpleasant sounds when distorted, and there is no �headroom� after the 0 mark. If recording digitally from a commerciallyproduced CD, the volume set in the menu should be 0 dB. This will maintain all the dynamic range of the source CD without clipping. Only boost the signal if the source is exceptionally quiet. An analog signal input at nominal level, with no cut or boost from the volume controls, is equivalent to a reading of �1 dB on the meters.
Do not vibrate the unit or turn off the power when the unit writes to the disc, otherwise, recording will fail.
Time display while recording
When in record or record ready mode, repeated presses of the TIME key cycle through four different time modes:
� Elapsed track time (no display light indication) � Remaining track time (REMAIN is lit in the display) � Elapsed disc time (TOTAL is lit in the display) � Remaining disc time (TOTAL and REMAIN are lit in the display)
Full disc
If the disc becomes full during recording, the unit will automatically insert a fade-out. For example:When recording a long program, just before the end of the disc is reached, the unit starts a fade-out over four seconds and the display will show Fade Out. When the fade-out has finished, the display shows Disc Full!. Press the STOP key to exit. If the disc is a CD-RW, the final track can be erased, if required (see �Erasing� on page 32) and the disc then finalized. If the disc is a CD-R, it must be finalized prior to use (see �Finalizing� on page 31).
TASCAM
CD-RW901
|
|
|
> |
|
