|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Manual correct, and complete. Downloads cleanly. Format of manual was presumably difficult to PDF to A4, but works reasonably well.
 ;
This was a hard to find manual. When I did find it , some sites wanted way too much for the file.
Owner-manual .com had it for a really reasonable price. Not only that but it was sent very quickly and was a quality scanned document, unlike some others I purchased from a different site.
Good job guys!!
Larry
 ;
Fast and courteous service. Product delivered as described. Thank you.
 ;
Last week I bought a second hand Panasonic AG-7500 SVHS Hi-Fi Video Cassette Recorder. It is a professional machine with many video and audio options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
 ;
The owner's manual/operating instructions that I purchased was the original factory document and it was in at least three and maybe more languages. I no longer have it because I sold the tape recorder and included the owner's manual/operating instructions and a service/repair manual that I bought on ebay for the new owner.
AUDIOACCESS CONSUMER DIGITAL INTERFACE� DEALER DOCUMENT
Revised 4/4/96
What is CONDI� and how does it work?
CONDI� is a communications protocol developed by Audioaccess for the purpose of controlling audio and video equipment. It is based on the EIA RS-485 electrical specification and utilizes collision sensing to allow multiple devices to send and receive on the same pair of wires. Data is communicated at 9600 baud, 8 data bits, 1 stop bit, and no parity. Before beginning data transmission, the bus should be checked for inactivity. If the bus is free, transmission may commence. If the bus is being used, wait for a period of inactivity. Each transmission should be checked against the intended message, to ensure that data corruption did not occur due to multiple devices attempting to use the bus at the same time. For each valid data transmission not originating from the main controller (except Status Requests which require a different response), the main controller will automatically generate an acknowledgment (38h) (i.e. any information coming into the main controller gets an ACK). The device which sent the data should receive this acknowledgment before beginning its next data transmission. Under rare circumstances, the main controller may be performing a function which cannot be interrupted. The data should be retransmitted until an acknowledgment is received. Due to this fact, delays are required between incoming commands for the transmission of the required acknowledgment.
How does Audioaccess use CONDI� ?
Audioaccess products use the CONDI� protocol to communicate between keypads, multiple products, and the main controller. For example, whenever a button is pressed on a KPS keypad, the keypad transmits a data packet (as outlined on the following pages) to tell the main controller which button has been pressed. The keypad will continue to resend the data packet every 150 mSec until the main controller sends an acknowledge back. More specifically, whenever a button is pressed on a KPS keypad, two commands are transmitted. The first command occurs when the button is initially depressed and is referred to as the �DOWN CODE�. The main controller will respond with an �ACKNOWLEDGE� code within 150 mSec. The main controller will additionally send a �LED ON� code corresponding to the button which was depressed. The second keypad command occurs either when the button is released or when the button is depressed for more than two seconds. These two commands are referred to as the �UP CODE� and the �LONG CODE�, respectively. This is but an example of how CONDI� is used by Audioaccess products. The other types of CONDI� codes, such as Computer codes, work very similarly.
What is this document?
The first section of this document describes the structure of a CONDI� code and what each byte means. The second section demonstrates the construction of sample CONDI� codes. The subsequent sections list all of the available CONDI� codes for each device type. Appendix A contains a description of the data bytes necessary to set the MRX tuner to a desired frequency. Note: the symbols �b�, �d�, and �h� used in this document denote binary, decimal, and hexadecimal values, respectively. All transmissions must be in eight-bit hexadecimal bytes.
Page 3 of 15
|
|
 |
> |
|