|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
;
Service Manual that I received was very helpful to me. Thank you.
;
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
;
Very useful service manual, was exactly what i needed.Good quality,reasonable price.Thank you.
5. Transfer of Electric Charge by the Horizontal CCD The transfer system for the horizontal CCD emplays a 2-phase drive method.
VAA11701-R.3571.A
The electric charges sent to the final stage of the horizontal CCD are transferred to the floating diffusion, as shown in Fig. 1-6. RG is turned on by the timing in (1), and the floating diffusion is charged to the potential of PD. The RG is turned off by the timing in (2). In this condition, the floating diffusion is floated at high impedance. The H1 potential becomes shallow by the timing in (3), and the electric charge now moves to the floating diffusion. Here, the electric charges are converted into voltages at the rate of V = Q/C by the equivalent capacitance C of the floating diffusion. RG is then turned on again by the timing in (1) when the H1 potential becomes deep. Thus, the potential of the floating diffusion changes in proportion to the quantity of transferred electric charge, and becomes CCD output after being received by the source follower. The equivalent circuit for the output circuit is shown in Fig. 1-7.
���
�� �� �� �� �� ��� �� ������� �� ������������������ �� �� �� ������� �� �� ����� �� ���� �� ���� �� ��� ��� ���
���
��
��
��
��
�� ���
���
��
��
��
��
�� ���
�� ������� �������
�������������������� �������������� �����������
Fig. 1-6. Horizontal Transfer of CCD Imager and Extraction of Signal Voltage
����������������
������������������������������
6. Lens drive block 6-1. Shutter drive The lens driver IC (LB8649FN) is used to drive by the two shutter drive signals (SIN1, SIN2) which are output from the ASIC expansion port (IC106), and the shutter is opened and closed. 6-2. Focus drive The focus stepping motor drive signals (FIN1, FIN2, FIN3
���������������������
���������� �������������� ��������� ������
and FIN4) which are output from the ASIC expansion port (IC106) are used to drive by the lens driver IC (LB8649FN). Detection of the standard motoring positions is carried out by means of the photointerruptor (FPI) inside
��������������������������� ���������������������������� ������������ ������������
the lens unit. 6-3. Zoom drive The zoom stepping motor drive signals (ZIN1, ZIN2, ZIN3 and ZIN4) which are output from ASIC (IC102) are used to drive by the lens driver IC (LB8649FN). Detection of the standard zoom positions is carried out by means of photoreflector (ZPI) inside the lens unit. 6-4. Iris drive The iris motor drive signals (IIN1 and IIN2) which are output from the ASIC (IC102) are used to drive the lens driver IC (LB8649FN).
Fig. 1-7. Theory of Signal Extraction Operation
- E3 ï½¥ E2500 -
|
|
|
> |
|
