|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
 ;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
;
The product manual I received was exactly what I was looking for, delivered painlessly at a very fair price. I can't ask for any more than that.
;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
;
Last week I bought a second hand BAUKNECHT TRK4850 DRYER. It is a professional machine with many programs and switch options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
but kindly the distributions of the operating programs not find in the owners manual,can you help me to understand the operating programs instructions thank you
2-3-7.
Curl Checking and Adjustment � If the curl is large or there are clearances If the TG3 curl is large or clearances exist, replace the coaster (S) assembly. If the TG6 curl is large, or clearances exist, replace the coaster (T) assembly. If curls or clearances exist on the TG7, rotate TG7 and adjust its height.
Note: Be careful not to rotate TG7 excessively. For details on how to replace the coaster (S) / (T) assembly, refer to 2-2-13 on page 5-48.
� Checking / adjusting method Run the tracking tape (J-20) (exclusive) in the CUE mode or REV mode, and check that the tape runs along each flange. Also check that there are no large curls on each tape guide.
There should be no large curls on the upper flange of TG3 and TG6. TG1 TG2 TG3 TG4 Drum TG5 TG6 TG7 There should be no large curls on the upper and lower flanges of TG7. TG3 TG4 Coaster (S) assembly TG5 TG6 Capstan Use a mirror (J-15) for checking for TG7. Easy to check with removing the damper assembly. (Refer to 2-2-3. Damper Assembly on page 5-41.)
TG2
Drum Coaster (T) assembly
TG1
TG7
2-3-8.
CUE / REV Check
2-3-9.
Rising Check
� Checking method Run the tracking tape (J-20) in the CUE mode or REV mode, and check that the intervals of the waveform peaks are consistent.
CUE mode
� Checking method Check that when the tracking tape (J-20) is switched from the STOP, CUE, REV, FF, REW modes to the PLAYBACK mode, the waveform rises horizontally within 2 seconds. Perform this 2 or 3 times.
Mode changes
STOP CUE REV PLAYBACK PLAYBACK
When switching the modes,
PLAYBACK the waveform should rise
within 2 seconds 2 or 3 times.
REV mode
FF REW
PLAYBACK PLAYBACK
� Check after checking rising � Check that the tape loads and unloads smoothly. � Play a self-recorded or already recorded tape, and check that the sound and images are normal.
� If not even If the waveform peaks are not even, perform "Tracking adjustment" again.
5-55
|
|
|
> |
|
