|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
complete part-lists and pcb layout, schematic diagram is good enlargable,
;
Excellent, fast delivery, excellent product. Good luck!
;
This manual is for the usa model only. But it is clear
, accurate and comprehensive, including board layouts and schematics.
I found it extremely useful for my mitsubishi dp-86da, but the same diagram would also work for the realistic lab5000 and hi fi 80. Thanks.
;
Great to have extra resources for Service Manuals, Now days you can really not trouble shoot efficiently without one , Wayne at IRIONS TV & ELECTRONICS REPAIR Clearwater , Fl. 33755 727-446-7955
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
FO-77TH/UX-73TH/GQ-72TH/FO-57TH/ UX-53TH/GQ-52TH/FO-27TH/UX-23TH/GQ-22TH
3. Connecting the power cord
prong) outlet.
1Plug the power cord into a 220 - 240 V, 50/60 Hz, earthed AC (2� When disconnecting the fax, unplug the telephone line cord before
unplugging the power cord. � Caution: Do not plug the power cord into any other kind of outlet. This will damage the machine and is not covered under the warranty.
6. Attaching the original document support
Attach the original document support as shown below.
� The machine does not have a power on/off switch, so the power is
turned on and off by simply plugging in or unplugging the power cord.
3. Loading the thermal paper (FO-20PR)
� � Your fax machine prints incoming faxes on a special kind of paper called fax paper. The fax machine�s print head creates text and images by applying heat to the thermal paper.
1Grasp the finger hold as shown and pull up to open the operation
panel.
4. Connecting the telephone line cord
1Insert one end of the line cord into the socket on the back of the
machine marked TEL. LINE. Insert the other end into a wall telephone socket.
TEL SE . T T EL LIN . E
2Flip up the front paper guide.
FO-57 UX-53 GQ-52 FO-27 UX-23 GQ-22 FO-77 UX-73 GQ-72
Dial mode: The fax machine is set for tone dialing. If you are on a pulse dial line, you must set the fax machine for pulse dialing. Press the keys on the operation panel as follows:
Press the knob to mark sure the front side of the metal guide is down.
1 2 3
Press
FUNC.
once and 4
once.
Display:
OPTION SETTING
3If you are loading paper that is 210 mm in width, place the paper roll
shims on each side of the paper compartment. (Note that Sharp recommended paper, including the initial roll, is 216 mm in width.) � The ribbed side of the shims should face in (toward each other).
Press
4 times.
DIAL MODE
Select the dial mode: TONE:
1
PULSE:
2
4
Press
STOP
to exit.
5. Moving your fax and reconnecting
If it is necessary to move your fax to a new location, first disconnect the telephone line cord before disconnecting the power cord. When reconnecting, it is necessary to connect the power cord before connecting the telephone line cord.
1�6
|
|
|
> |
|
