|
|
|
Who's Online
There currently are 4837 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
EN
19
1 2
Set the Power Dial to � A � while pressing down the lock button located on the dial.
SELECT OPERATION MODE
NOTES:
PULL OUT VIEWFINDER OR OPEN LCD MONITOR
Pull out the viewfinder fully or open the LCD monitor to approx. 90° degrees. �The lens cover opens, the power lamp comes on and the scene you're aimed at appears. �The Record-Standby mode is engaged.
3 4
START RECORDING
When �PAUSE� appears, press START/STOP. A beep signals the start of recording and the tally lamp comes on.
� The image will not appear simultaneously in the LCD monitor and the viewfinder. No image appears on the LCD monitor when the viewfinder is pulled out. It is not possible to shoot using both LCD monitor and viewfinder. However, during Interface Shooting ( pg. 23) the image appears simultaneously in the LCD monitor and the viewfinder. � If 5 minutes elapse in the Record-Standby mode, power shuts off automatically to conserve energy and protect the heads. To turn the camcorder on again, push back and pull out the viewfinder again or close and re-open the LCD monitor. As long as you don�t take out the tape you were using or play it back, you can continue from where you left off with no noticeable brake on the �
STOP RECORDING
Press START/STOP again to stop recording. �The camcorder re-enters Record-Standby mode.
5 END RECORDING
When you�re finished recording, push back the viewfinder or close the LCD monitor until it clicks; the lens cover closes and the power lamp goes out. �When transporting, make sure the viewfinder is pushed back and the LCD monitor is closed and locked. �To turn power on again, pull out the viewfinder or open the LCD monitor.
� �
�
OR
Set the Power Dial to �OFF�. �When turning to �OFF�, it is not necessary to press down the lock button. �
recorded video. When a blank portion is left between recorded scenes on the tape, the time code is interrupted and errors may occur when editing the tape. Continue recording from where you stop so there are no gaps by following "Recording from the middle of a tape" ( pg. 20). Record-Standby means that a tape is loaded and the camcorder is ready to record. During recording, sound is not heard from the speaker. If you want to hear the sound, connect optional headphones to the headphones jack. The sound volume at this point is the same as the level it was adjusted during playback. To make the indications disappear, press and hold the ON/OFF button for more than approx. 1 second. However, it is impossible to remove the tape running indicator � 444� and warning indications and so on ( pg. 81). Use the viewfinder when under direct sunlight or when reflections make it difficult to see the LCD monitor.
|
|
|
> |
|
