|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual you sent me was excellent. It included clear, readable diagrams and a usable parts list. I would surely use your service again. Thanks
;
Payments were processed quickly and items were exactly as described. I will use owner-manuals.com in the future for any other manual needs.
;
The Technics manual was very clear and I was able to solve my technical problems.
I did not think that anyone kept these manuals and was pleasantly surprised to find them on the Internet and at an affordable price.
I would recommend Owner Manuals as a first source of technical products for ‘dated’ equipment manuals.
Ian
;
The content of the manual was not found on the Internet and was a hard find. I check the net for 5 hours until I came across this web-site. When I did find the book it Auto loaded into my IPAD PDF shelf for books for review at anytime. Overall I am satisfied with the book and it answered all my questions. This repair book is obsolete because the product I bout it for is pretty old. Thanks for the help with the download and even having the manual. Thanks 73's K5HRD
;
Excellent manual including schematics. The service was great and the manual helped complete the job.
CD SECTION
Note: 1. CD Block is basically constructed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10M� impedance. 4. Clean the object lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. S Curve Check
oscilloscope BD board
Note: Clear RF signal waveform means that the shape ��� can be clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV : 200mV TIME/DIV : 500ns
level : 1.75 ± 0.25 Vp-p
E-F Balance (Traverse) Check
oscilloscope BD board
TP (FE) TP (VC)
+ �
TP (TE) TP (VC)
+ �
Adjustment Location: BD board Procedure : 1. Connect the oscilloscope to test points TP (FE) and TP (VC). 2. Connect TP (FEI) and GND, and TP (AGCCON) and GND of the BD board with lead wires. 3. Press the 1/u button to turn the set ON. 4. With the disc (YEDS-18) loaded, press the ^ button and perform focus search. (Focus search will be performed in the same way even while the disc table is pushed in and out.) 5. Check the symmetry and peak to peak level of the oscilloscope waveform (S curve) at this time.
S-curve waveform
symmetry
Adjustment Location: BD board Procedure : 1. Connect oscilloscpe to test point TP (TE) on BD board. 2. Short-circuit SL502 of the video board to GND. 3. Turned Power switch on. Press FUNCTION button to select CD. 4. Put disc (YEDS-18) in to play the number five track. 5. Press the PLAY MODE/DOLBY NR button. (The tracking servo and the sledding servo are turned OFF.) 6. Check the level B of the oscilliscope's waveform and the A (DC voltage) of the center of the Traverse waveform. Confirm the following : A/B x 100 = less than ± 22%
Traverse waveform A Within 4.0 ± 1.0 Vp-p B 0V B A (DC voltage) Center of the waveform
6. After check, remove the lead wire connected in step 2. Note: � Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. � Take sweep time as long as possible and light up the brightness to obtain best waveform. Adjustment Location: BD board RF Level Check
oscilloscope BD board TP (RF) TP (VC) + �
level : 1.3 ± 0.6 Vp-p
7.
Press the PLAY MODE/DOLBY NR button. (The tracking servo and sledding servo are turned ON.) Confirm the C (DC voltage) is almost equal to the A (DC voltage) is step 7.
Traverse waveform
0V
C (DC voltage)
Procedure : 1. Connect oscilloscope to test point TP (RF) and TP (VC) on BD board. 2. Connect TP (AGCCON) and GND of the BD board with lead 3. 4. 5. 6. wires. Press the 1/u button to turn the set ON. Put disc (YEDS-18) in and playback 5track. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not. After check, remove the lead wire connected in step 2.
Tracking servo Sled servo OFF
Tracking servo Sled servo ON
8.
Desolder the short-land (SL502) short-circuited at step 2.
Adjustment Location: BD board
16
|
|
|
> |
|
