|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
POWER-HANDLING LIMITATIONS
The power-handling capability of any woofer is related to both its ability to dissipate heat and the maximum excursion limits of its cone. Once the speaker�s voice coil moves outside the magnetic gap, power can no longer be converted into motion and all the amplifier�s power is converted into heat in the voice coil. This voice-coil heating is the largest detriment to speaker longevity, so overexcursion should be avoided. Since speakercone excursion is different for each type of enclosure, power handling is different for each enclosure. Sealed enclosures exert the most control over the motion of a subwoofer because the air inside the box acts like a spring against the motion of the woofer cone. Larger boxes allow for more excursion, thus providing more low-frequency output for the amount of power used. When placed in a sealed box larger than the Vas of the subwoofer, it will perform as if it were in an infinite-baffle installation. Vented and bandpass enclosures have the lowest amount of excursion for the amount of sound output. This is a result of port output reinforcing the sound output from the woofer. The mass of the air contained in the port provides an acoustic load on the woofer�s cone at the tuning frequency, and this added mass decreases woofer-cone excursion. Vented boxes do not provide adequate woofer control when driven below the port-tuning range, so proper design is important. A vented bandpass box will have the lowest overall cone excursion provided a subsonic filter is used. � Voice-coil overheating and burning due to overexcursion are often caused by overdriving an amplifier into �clipping. A severely clipped � signal, or squarewave, contains nearly twice the power of a clean sine wave at the same level. Bass that sounds broken up and distorted at higher volumes is usually indicative of an amplifier that is clipping and being asked to deliver power beyond its rated power. � Infinite-baffle or �free-air� mounting applications allow for greater cone excursion than subwoofers mounted in an enclosure. In order to compensate, recognize that the power-rating value of the subwoofer will likely be half its rated power in this application. � Study the excursion curves on the enclosed Kappa Series data sheet and note the differences for different enclosure applications. The type and size of box used will produce different excursion demands on the enclosed subwoofer and, consequently, different levels of power handling. As long as recommended parameters are used, the subwoofer will perform properly in its enclosed environment. However, any design deviation may result in less than optimum performance, and may also subject the subwoofer to overexcursion (i.e., where the voice coil leaves the gap) that can eventually damage the speaker. For additional help with this issue, please contact your authorized Infinity dealer.
SPECIFICATIONS
Kappa 80.1w Configuration: Nominal Impedance: Power Handling: Sensitivity @ 2.83V/1m: Frequency Response: Mounting Depth: Cut-out Diameter: Kappa 100.1se Configuration: Nominal Impedance: Power Handling: Sensitivity @ 2.83V/1m: Frequency Response: Mounting Depth: Cut-out Diameter: Kappa 120.1se Configuration: Nominal Impedance: Power Handling: Sensitivity @ 2.83V/1m: Frequency Response: Mounting Depth: Cut-out Diameter: 8" woofer 4 ohms 100W rms/400W peak 93dB 30Hz � 300Hz 4" (102mm) 7-3/16" (183mm) Kappa 100.1dvc Configuration: Nominal Impedance: Power Handling: Sensitivity @ 2.83V/1m: Frequency Response: Mounting Depth: Cut-out Diameter: Kappa 120.1dvc Configuration: Nominal Impedance: Power Handling: Sensitivity @ 2.83V/1m: Frequency Response: Mounting Depth: Cut-out Diameter:
10" subwoofer 4 ohms 250W rms/1000W peak 93dB 25Hz � 250Hz 5-1/16" (129mm) 8-7/8" (226mm)
10" subwoofer 4 ohms per voice coil 250W rms/1000W peak 93dB 25Hz � 250Hz 5-1/16" (129mm) 8-7/8" (226mm)
12" subwoofer 4 ohms 300W rms/1200W peak 94dB 20Hz � 250Hz 5-13/16" (148mm) 10-13/16" (275mm)
12" subwoofer 4 ohms per voice coil 250W rms/1000W peak 94dB 25Hz � 250Hz 5-13/16" (148mm) 10-13/16" (275mm)
|
|
|
> |
|
