|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
 ;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
;
The manual was properly scanned and perfectly readable. The only small problem is that I couldn't use my dear Ctrl + F to find a word I needed.
HHHHHHHHHHHHHH Audio Adjustments
Section
07
3 Press c or d to select the phase of subwoofer output. Press c to select reverse phase and Rev. appears in the display. Press d to select normal phase and Normal appears in the display.
# When the subwoofer controller setting is only S.W Control:EXT, you can switch to the non fading output on/off setting. (Refer to page 31.)
Adjusting subwoofer settings
When the subwoofer output is on, you can adjust the cut-off frequency and the output level of the subwoofer. 1 Press AUDIO to select Sub-W2. Press AUDIO until Sub-W2 appears in the display.
# When the subwoofer output is on, you can select Sub-W2.
2 Press a to turn non fading output on. NonFad ON appears in the display. Non fading output is now on.
# To turn non fading output off, press b.
Adjusting non fading output level
When the non fading output is on, you can adjust the level of non fading output. 1 Press AUDIO to select non fading output setting. Press AUDIO until NonFad 0 appears in the display. 2 Press a or b to adjust the output level of the non fading. Each press of a or b increases or decreases the level of the non fading. +6 6 is displayed as the level is increased or decreased.
2 Press c or d to select cut-off frequency. Each press of c or d selects cut-off frequencies in the following order: 5080125 (Hz) Only frequencies lower than those in the selected range are output from the subwoofer. 3 Press a or b to adjust the output level of the subwoofer. Each press of a or b increases or decreases the level of the subwoofer. +6 6 is displayed as the level is increased or decreased.
Using the high pass filter
When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn the HPF (high pass filter) on. Only frequencies higher than those in the selected range are output from the front or rear speakers. 1 Press AUDIO to select HPF. Press AUDIO until HPF appears in the display. 2 Press a to turn high pass filter on. HPF 80 Hz appears in the display. High pass filter is now on.
English
Using non fading output
When the non fading output setting is on, the audio signal does not pass through this units low pass filter (for the subwoofer), but is output through the RCA output. 1 Press AUDIO to select non fading output on/off setting. Press AUDIO until NonFad ON appears in the display.
# To turn high pass filter off, press b.
En
27
|
|
|
> |
|
