|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very good quality original datasheet!I like this amazing website!!!!!!
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
RCD-W10
4-5. CD-RW Recording Adjustment and Self Record/Playback Check 1) Select the menu as follows. Control � Macro, and select 05cdrw_S.ttl. Press �Open�. Place the test CD disc PATD-012 on the Deck A. Place the recording CD-RW disc (see Note: 4-5-1) on the tray (Deck B) as prompted by the display and press �OK�. (Fig. 4-43) Note : 4-5-1 The disc to be used in this step. * * Use the CD-RW disc CWM74 for audio, that is manufactured by Sony. The disc that is used by this step cannot be used for the general purposes and for the purpose of operation check of the RCD series equipment as it is. The disc that is used for the general purposes or for the purpose of operation check of the RCD series equipment, cannot be used in this step. When you want to use the CD-RW disc for other applications, erase the CD-RW disc. If the recording is interrupted by any reasons during the recording operation (i.e., the WRITE POWER ON LED of the jig is lighting), the disc cannot be used any more in the subsequent step. In such a case, erase the CD-RW disc and repeat this step from the very beginning again. When the disc that is used in step 2) is the disc that has been used in the electrical adjustment in the past. ....... Press �Yes�. When the disc that is used in step 2) is a completely blank disc. ......... Press �No�. (Fig. 4-44)
4 Fig. 4-44 4 Fig. 4-43
2)
*
3)
Note : The recording CD-RW disc can be used only for the electrical adjustment. The recording CD-RW disc must be controlled so that it must not be used for any other applications. 4) Press the H button of Deck A. After playback starts, press �OK�. (Fig. 4-45)
4 Fig. 4-45
5)
When the message as shown in Fig. 4-46 appears some seconds later, select 4x of the test mode (refer to page 19, Play Speed Selection Mode (Deck A)) PLAYBACK SPEED. Then press the H button of Deck A. After playback starts, press �OK�.
4 Fig. 4-46
44
 $4.99 RCDW10 SONY
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
